All Forums
Browse the Community
USB
Universal Serial Bus (USB) forums have discussions regarding Low-Full & High Speed Peripherals, Superspeed Peripherals, USB Hosts Hubs Transceivers, and USB EZ-PD Type C product solutions for PCs and consumer device topics.
Wireless Connectivity
Power
Sensors
Memories
Memory Discussion Forums discussions regarding NOR Flash, SRAM, nvSRAM and F-RAM - performance and reliability with discrete memory densities ranging from 4K-bit to 2G-bit topics.
Other Technologies
Discussion forum regarding Other Technologies including Power Management and Clocks topics.
Security & Smart Card
Radio Frequency (RF)
Software
Software including ModusToolbox, PSoC Creator, WICED Studios and Wi-Fi Bluetooth for Linux .
Applications
Featured Discussions
Dear supporter,
I would like to translate the following KBA. Could you confirm?
PSoC™ 6 MCU with Bluetooth® LE: Reading sleep clock accuracy – KBA238648
https://community.infineon.com/t5/Knowledge-Base-Articles/PSoC-6-MCU-with-Bluetooth-LE-Reading-sleep-clock-accuracy-KBA238648/ta-p/690974
Bestregars,
JUTA_2823561
Hi Infineon.
Below is sample code for DFU(device firmware upgrade).
https://github.com/Infineon/mtb-example-psoc4-dfu-basic
This sample code explains DFU using I2C or UART.
Is there any sample code for DFU using SPI?
Is my understand correct that PSoC4 can use SPI for DFU?
Or can only I2C or UART be used in DFU and not use SPI?
Best Regards.
YuMa
Show LessHello,
I am trying to connect Infineon Miniwiggler v3 to the Aurix Tc387, by using Infineon Memtool 2021.8.
But couldn't able to establish the connection between them.
Need support related to Memtool Settings and need details for DAP Miniwiggler v3.
Please support!!
Show LessThe user use the Hyper Flash S26KS128SDPBHB020; Could you tell me the init program of S26KS128SDPBHB020; Dose the S26KS128SDPBHB020 need the "init program" that was translated by the Controller through "Hyper" or "SPI"? 此型号Flash在使用的时候,需要Init 程序吗 ?在哪儿下载呀 非常感谢
Thanks
Show LessWhat is the relationship between the magnitude of the IGBT turn-off voltage (e.g. -9V vs. -15V) and the turn-off time, turn-off voltage spike, and losses?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/IGBT%E5%85%B3%E6%96%AD%E7%94%B5%E5%8E%8B/td-p/713675
Show LessWe are requirement of supporting I2C master-slave mode for our I2C1 port. Can I Get some example regarding the same.
I hope this message finds you well. I am reaching out regarding a couple of questions I have about the datasheet for the IR2109(4)(S).
Firstly, I am curious about the capacitor specifications mentioned in the datasheet. I noticed that polarized capacitors are recommended for certain applications. However, I am interested in exploring the possibility of using non-polarized capacitors instead. Could you kindly provide some insight into whether non-polarized capacitors can be safely substituted for the polarized ones mentioned in the datasheet?
Secondly, upon attempting to calculate the value of the bootstrap capacitor using the provided formula, I encountered an unexpected result. Specifically, when I substituted the given values into the formula, I found that the denominator resulted in a negative value: (Vcc - Vf - VLs - Vmin) = (12V - 1V - 2.35V - 9V) = -0.35V. This negative value raises some concerns and prompts me to seek guidance on how to proceed with determining the appropriate value for the bootstrap capacitor. Could you please provide clarification on whether a negative value in this context is valid, or if there might be an alternative method or consideration to account for in this calculation?
I understand the importance of adhering to recommended component specifications and calculations, but I am curious about any potential flexibility or alternative approaches in these matters. Any guidance or clarification you could offer on these issues would be greatly appreciated.
Thank you very much for your attention to these inquiries. I look forward to hearing from you soon.
Best regards,
Show LessHello,
the FX3 TRM has chapter 10.9.4 UIB_POWER with register definition.
It specifies RESETN bit as only readable (R) by software. The description says:
```
After setting this bit to 1, firmware will poll and wait for the ‘active’ bit to assert. Reading ‘1’ from
‘resetn’ does not indicate the block is out of reset – this may take some time depending on initializa-
tion tasks and clock frequencies.
```
Is this bit writable from software (firmware) or is it read-only?
Additionally, 10.17.2 UIBIN_POWER has RESETN defined as R/W and description says:
```
This bit is nonfunctional for UIBIN and will not reset anything. Use UIB_POWER register instead.
```
Can you please clarify this discrepancy?
Thank you
Show LessHello Team
Part Number : IRLML6402TRPBF
I need RoHS, REACH documentation for that part.
I would like to receive a link to receive the materials or a reply by email.
-
TraveoII
UART buadrate Setting
by chandan1995 Jun 19, 2023