PSoC™ 6 Forum Discussions

Hi,

 I am developing a BLE application CY8CKIT-062-BLE board, trying to implement BLE DFU.

  I followed the application note "CE216767",  the manual guided me firstly to program App0 through PSoC creator, then using CySmart to update App1 by BLE. I can successfully follow this flow, and App1 works normally.

 However, for mass production, I want to use wire to program App1 for the initial programming of the products.

 I tried to use PSoC creator to program App0 first, then also use PSoC creator to program App1. But after the programming of App1, App1 is not working. Then I push the Reset button on the board, but still, the App1 is not working.

So, my question is: is it possible to both program App0 and App1 without using Cysmart?  Could you please let me know how to do that?

Thank you very much for your reading! 

Looking forward to your help and suggestions.

Best regards,

Jiabin

Dear Experts.

Using CY8CKIT-062-WiFi-BT (PsoC6 WiFi-BT Pioneer Kit), i'm testing to use CSD Capsense & CSDADC functions at the same time.
CAPSENSE™ Middleware Library 3.0: High-level Functions (infineon.github.io)

With reference to the above, I am testing by switching Capsese and CSDADC.
I checked the mode conversion and CSDADC was read normally.

However, CapSense does not work properly.
I'm try to fix everything, it doesn't work.

Please help if there are any mistakes or areas that need to be corrected.

***

This is a project created by adding CSDADC and SARADC to the CAPSENSE_Buttons_and_Slider example.

(File Attached)

CSDADC: P1_2, P1_3, P1_4
SARADC: P10_0, P10_1, P10_4, P10_5
CAPSENSE: BTN: P8_1, P8_2,
Slider : P8_3~7

thank you

I have two PSoC 6 kits ( PSoC 62 and PSoC 64). I aim to read and write on an SD card from the PSoC controller. Both boards have SD card holders, but I can not find an example of interfacing with it. 

Please share the link.

Hi All,

I am planning to interface a TFT LCD display having SPI interface with emWin library using PSOC6 on PSOC creator IDE.

I have gone through the example CE223726 – PSoC 6 TFT Display Interface with EmWin Graphics Library. , which uses 8-bit parallel interface and not SPI. The display has the ILI9488 as the driver IC and it has support for emWin.

1. Can anyone help me on how to proceed with changing the example code's  parallel interface to SPI  ?
2. Is there any update for PDL for supporting SPI in GraphicLCDIntf_1 component ?

regards,

Vinu

Tested it with CY8CKIT-062-BLE and CY8CKIT-062-WIFI-BT,
Modus ToolBox and VSCode.
-------
https://github.com/Infineon/mtb-example-psoc6-dual-cpu-ipc-pipes or
project creator
   CY8CKIT-062-BLE
      Peripherals
         Dual-CPU IPC Pipes

Right out of the box, VSCode detects two problems in the code for cm0p:

main.c   app-cm0p
identifier "NvicMux7_IRQn" is undefined C/C++(20)[Ln60, col 28]
struct "<unnamed>" has no field "cm0pSrc" C/C++(136)[Ln61, col 5]

surprisingly, the compiler does not detect the errors, compiles the code
and runs on the target kit without detectable errors...
I am not well versed using Eclipse, but, it does not seem to be aware of the
problems and it compiles fine too. (same tool chain)

the lines with the issue are:

const cy_stc_sysint_t mcwdt_int_cfg =
{
.intrsrc=(IRQn_Type) NvicMux7_IRQn, // 7
.cm0psrc=srss_interrupt_mcwdt_0_IRQn, // 19
.intrPriority = 2 //
};

The problem in the first line can be bypassed by replacing it with:
.intrsrc=(IRQn_Type) 7

The second line issue is a bit more convoluted...

After all the #ifdefine lines are resolved, the stucture   cy_stc_sysint_t
presented to main.c (app_cm0p) does not have a cm0pSrc field.
it appeared that it was missing the definitions in
#include "cy8c6347bzi_bld53.h" (CY8CKIT-062-BLE)
but, adding it to the #include list made no difference.

----------------------------------
Another unrelated problem in IPC code:

the structure definition for ipc_msg_t
lines 104-111 of ipc_communication.h
is:
typedef struct __attribute__((packed, aligned(4)))
{
   uint8_t client_id;           <-- is this supposed to be uint32_t ???
   uint8_t cpu_status;
   uint16_t intr_mask;
   uint8_t cmd;
uint32_t value;
} ipc_msg_t ;

Cy_IPC_Pipe_RegisterCallback(...) expects uint32_t
and the documentation says it is an uint32_t.

Starting a project using CY8C6245LQI-S3D42.  This does not seem to be supported by PSOC Creator, so I tried installing ModusToolbox.  However I cannot create even a simple project. (I tried multiple BSPs and starting projects)

The IDE fails at Step 5 in Quick Start Guide.  I get the following error when using the Project Creator 1.40  (File>New> Modustoolbox application>... etc)

BSP: CY8CPROTO-062S3-4343W
Template Application(s): ADC basic
Application(s) Root Path: C:/Users/******/Documents/gitDev/******
Press 'Create' to create the selected application(s).
Collecting application data...
Info: The following entered on the command line will create the exact same project as that created with the GUI tool:
C:/Users/*****/ModusToolbox/tools_2.4/project-creator/project-creator-cli.exe --board-id CY8CPROTO-062S3-4343W --board-uri https://github.com/cypresssemiconductorco/TARGET_CY8CPROTO-062S3-4343W --board-commit latest-v2.X --app-id mtb-example-psoc6-adc-basic --app-uri https://github.com/cypresssemiconductorco/mtb-example-psoc6-adc-basic --app-commit latest-v1.X --cypress-tools C:/Users/******/ModusToolbox/tools_2.4 --target-dir C:/Users/*******/Documents/gitDev/******* --user-app-name ADC_basic --output-for-machine --use-modus-shell
==============================================================================
= Cloning 'mtb-example-psoc6-adc-basic' =
==============================================================================
Cloning https://github.com/cypresssemiconductorco/mtb-example-psoc6-adc-basic into C:/Users/*******/Documents/gitDev/******* directory...
env git clone --progress --origin cypress https://github.com/cypresssemiconductorco/mtb-example-psoc6-adc-basic ADC_basic
Cloning into 'ADC_basic'...
fatal: invalid branch name: init.defaultBranch =
Project 'mtb-example-psoc6-adc-basic' failed to create.
'git clone' failed.
Failed to create and export 'ADC_basic' application.

Hi,

I'm trying to run the example "secure blinky LED FreeRTOS"  with CY8CPROTO-064B0S3 on Mac

While building the example in ModusToolbox by clicking "Build Secure_Blinky_LED_FreeRTOS Application", I've faced errors : ModuleNotFoundError: No module named 'cysecuretools'

Following the instructions written in the user manual, I've already installed cysecuretools by using pip before it.

When I've executed the build command directly on the local terminal, the hex files have been created properly.

Should I set a specific path for cysecuretools in ModusToolbox?

The detail of error messages are below:

==============================================================================================

Linking output file mtb-example-psoc6-secure-blinky-led-freertos.elf

python3 /Users/jaebonglee/work/mtw_1/Secure_Blinky_LED_FreeRTOS/libs/TARGET_CY8CPROTO-064B0S3/psoc64_postbuild.py --core CM4 --secure-boot-stage single --policy policy_single_CM0_CM4 --target cyb06xx5 --toolchain-path /Applications/ModusToolbox/tools_2.4/gcc --toolchain GCC_ARM --build-dir /Users/jaebonglee/work/mtw_1/Secure_Blinky_LED_FreeRTOS/build/CY8CPROTO-064B0S3/Debug --app-name mtb-example-psoc6-secure-blinky-led-freertos --cm0-app-path ../mtb_shared/psoc6cm0p/release-v2.2.0 --cm0-app-name psoc6_03_cm0p_secure

Traceback (most recent call last):

  File "/Users/jaebonglee/work/mtw_1/Secure_Blinky_LED_FreeRTOS/libs/TARGET_CY8CPROTO-064B0S3/psoc64_postbuild.py", line 22, in <module>

    from cysecuretools import CySecureTools

ModuleNotFoundError: No module named 'cysecuretools'

make[1]: *** [CY_BUILD_bsp_postbuild] Error 1

make: *** [secondstage_build] Error 2

"/Applications/ModusToolbox/tools_2.4/modus-shell/bin/make CY_MAKE_IDE=eclipse CY_MAKE_IDE_VERSION=2.4 CY_IDE_TOOLS_DIR=/Applications/ModusToolbox/tools_2.4 -j9 all" terminated with exit code 2. Build might be incomplete.

09:07:53 Build Failed. 2 errors, 0 warnings. (took 6s.552ms)

==============================================================================================

Hello, 

I am trying to start up the Modus Toolbox using the Xcode app on a Mac since it says I am required to do so in this screenshot: 

 However I am unfortunately unfamiliar with Xcode and am a little lost right now.

 When I open the Xcode app and try to open ModusToolbox it shows this which I am confused on:

For mac am I able to use eclipse instead or do I have to use Xcode? 

Thank you!