PSoC™ 6 Forum Discussions

I want to get the system uptime since the chip is powered on and working, similar to the micros() and millis() macro in Arduino.

Is there any pre-built function available in PDL or I will have to create a custom function for that?

Thanks for any help!

Dan

Hello Team Cypress,

I am here to ask for a Cypress MCU that supports the following features.

The requirments are:
- The Cypress MCU will be used as Local Host MCU.
- The Cypress MCU must support Hardware Security Module (HSM) Multi2
- The Cypress MCU must support USB-IF (USB Interface)

Here is the block diagram where Cypress MCU is needed for the blue part of the blocks.

Would you share the best Cypress MCU part number with the features?

Thank you always.

Sincerely,
Ben

Hi,

To gain insights into the performance of Crypto HW on PSoC 6 Board (CYBLE-416045-02), I'm performing some measurements.

I get the following for AES Encryption using ECB mode for 1 Block of input data:

Client Server Model: 1795 CPU cycles 

Direct Crypto Core Access: 784 CPU cycles 

I'm looking for some feedback. So, is the performance in line with the expectation? Are there any performance measurements available for this board already?

Thank you!
Shiv

Hi All,

I am using PSoC 62 WiFi-BT Kit to read data from a sensor, store the data into a file, and upload the data file to an HTTP server (so users can download it to their computers).

I have done the sensor part, and I also know that Modus Toolbox has an 'emFile' example and 'AnyCloud HTTP' example for PSoC 6. My questions are:

1. I didn't see the SD card interface on the PSoC 6 side, but the 'emFile' example does provide me with the option to store the file into an SD card. Could you please give an example of how to store a file into an SD card? If not, could I access the file in the internal NOR flash?

2. The 'AnyCloud' example is using the 'HTTP Server' library, but it only gives three methods, GET, PUT, POST. Does it have any method to refresh the web page dynamically? I mean that could it refresh some numbers automatically on the web page which I want?

3. I may need to implement some nice visual representation on the web page. For example, real-time refresh bar plot. However, this is supported by some external sources based on Python and JavaScript. Is it possible to implement such functions in Modus Toolbox?

4. If these functions are too difficult to realize. Could you please give me some examples of Cloud Services which can do such things, I mean build a file for data, dynamic refresh, and figures plot?

Thank you so much for your patience and help!

Best regards,

Hank

Hello，

        1.Warnings as follow：        

        ../CODE/libs/mtb-pdl-cat1/latest-v2.X/cmsis/include/core_cm4.h:1775:22: warning: '__NVIC_ClearPendingIRQ' defined but not used [-Wunused-function]

        2.Problem description：

        After the first compilation of the project, there will be more than 30,000 warning messages as shown above, and after the second compilation, the warning messages will become 0. Looking at the file where the problem is located, you will find that it is all caused by quoting the pdl library in the libs file, but there is no problem with the pdl library.

        3.Question：

        How to remove these warning messages that should not be displayed, and not ignore the real error and warning .

        4.My own guess：

        It may be caused by the wrong way or path of calling the pdl library, but the problem has not been solved. 

        In summary, I have been troubled by this problem for a long time. If you can help me solve this problem, I would be very grateful. 

Best Wishes，

JCD        

GPIO LED on my PCB on when connected to programmer debugger MiniPro4 but cant toggle RGB LED on PCB

I am new to PSOC 6 microcontrollers, I have used ST, ATmel and Microchip and ATSAM ARM processors.

I am using a CY8C6347FMI-BLD53T and have 5 pin connection for programming and debugging. 

See attached for program connection, LED connection and software connected to 5 of my PCBs with  programmer debugger MiniPro4, 

I watched the 101 video and did the same software set up, just changed micro type and pin connection.

Project complies

Connects to my PCB, my Green LED on my PCB switches on when programming.

LED does not flash as per code

Thanks

Dom 

Hello Everyone,

Why is cy8ckit-064s0s2-4343w not supported in Modus Toolbox but cy8ckit-064b0s2-4343w is supported?

There aren't many differences between the two boards based on first-hand analysis the specifications provided on the website.

Can I use cy8ckit-064b0s2-4343w to configure and develop projects (in Modus Toolbox) for S0S2 board?

Any insights on this will be helpful 🙂

Regards,

Aditi Prakash