PSoC™ 5, 3 & 1 Forum Discussions
Hi CY team
We are Haier's partner. Due to our IQC needs, please provide CG7281AM(Haier part number ) silk-screen file.The corresponding common part number is CY8C22545-24AXI .
many thanks. Have a good day !!
Show LessSAR_ADCにあるoverrun_det フラグを使用して異常を検出したいのですが、
このフラグはデフォルトでDisableのようです。
Enableにできる(このフラグは使える)のでしょうか。
もしできるのであれば設定方法を教えてください。
-----------------------------------------------------
Is it possible to enable the overrun_det flag function in ADC_SAR_WRK1_REG?
If yes, please tell me how to enable.
Show Less
Hi everybody. I want to run AFE4400 to calculate SPO2 and Heart rate from AFE4400.I design a pcb file and connect AFE4400 with PSOC5 CY8C5468LTI_LP026
and connect spi and other pin that need to microcontroller.but I dont know why AFE4400 not responce to my write and read register function. Is there any body to know where is my mistake?
AFE4400 has a structure to read and write that I checked and I did them.Psoc creater and PCB and Schematic file attached here...
I checked SPI thata on MOSI to ensure data transfer has not any mistak but I do not seen MISO responce.here is my oscilloscope screenshot. Psoc creator file attached please tell me where is wrong?
please guide me to solve problem to read AFE4400 register data correctly.
Thanks for attention...
Show Less
Hi Team,
I have created a LED program which is in c. Wanted to convert to c#. Please let me know what are the steps to follow? I am using Cypress CY8CKIT-050 5LP.
Show LessHi team,
How to choose Pin and port for Cypress CY8CKIT-050 5LP. I am working on blinking the LED, but after building successfully when i select Debug -->Program i am getting the issue as below. Unable to select it. I am not sure what will be the port and pin execute it. Please help me on this...
Show LessHello,
Can I upgrade the KitProg firmware of my CY8CKIT-059 kit to KitProg3.
As I see that mode can be changed via the Programmer, so no need of switch and have to direct the additional IO's to the other headers.
I could find no information in this regards in the KitProg user guide.
The above kit is not listed in list of supported devices in the guide.
Thanks in advance.
Kuldeep
Show LessDear All,
I have a design with CY8C5268AXI-LP047 microcontroller.
I have an requirement of watchdog timer with reset time of 5 to 10 seconds.
The CY8C5268AXI-LP047 part has watchdog timer with time limit of 2 to 3 seconds only.
Anyone can help me to increase watchdog time up to 10 seconds?
Show LessHi,
Could someone help me understand how to cache images from SD Card to PSoC memory??? Is there an example to follow? I am using PSoC 5 LP and emFile to work with SD card. I want to save the time hence the try to cache images.
Appreciate any tips with this regard.
Thanks and regards,
Shamili
Show LessHi,
Can I produce 400Megahz square wave with the help of psoc?
BEST REGARDS
I read the 95 pages document for CLI guid
I am using Psoc 5 and I could connect to microcontroller to turn off LED but I cannnot release it to blinking again
after DAP_Acquire it will connect https://100001.onl/ https://1921681254.mx/ https://happymod.site/
1 >cd "C:\Program Files (x86)\Cypress\Programmer"
2 >ppcli.exe
3 >OpenPort KitProg/1E13146C03227400 .
4 >SetPowerVoltage 5
5 >PowerOn
6 >SetProtocol 8
7 >SetProtocolConnector 1
8 >SetProtocolClock 152
9 >HEX_ReadFile "H:\\P08.hex"
10 >DAP_Acquire
11 >DAP_AcquireChip
12 >DAP_GetJtagID
13 >PSoC3_GetTemp 0x1 0xFFF 0x4
14 >SetAcquireMode “Reset”
<
0 OK
15 >DAP_ReleaseChip
<
0 OK
16 >ReleaseChip
<
0 OK
untill line 13 the code will execute correctly and it turn off LED of microcontroller but after line 14 when I want to release the chip to turn on LED again I will not get the appropriate result as I expected, Please let me know if I miss some Api or if I should use another api