- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
i AM TRYING TO REBUILD THE RTD EXAMPLE OF PSOC3_4 FOR PSOC5LP KIT BUT MY RTD READINGS ARE NOT PROPER DUE TO IDAC NOT SOURCING PROPER 1MA CURRENT.
i TRIED 1MA SOURCING IN DIFFERENT EXAMPLE OF IDAC8 OF 5LP . HERE IT WORKS FINE BUT IN RTD EXAMPLE IDAC JUST SOURCE 0.22microamps and not 1ma.
please help as this is weird situation
Solved! Go to Solution.
- Labels:
-
PSoC 5LP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
I have tested the project as per your configuration on CY8CKIT059 kit. I have kept break points during Reference resistor measurement and RTD resistance measurement and I was able to see ~1mA current on both the pins using the multimeter. So the issue at your side might be something else. Could you please tell keep a breakpoint after the IDAC value is set and tell me the voltage at these pins? Your schematic says you are connecting less value resistnaces- so that should not be the issue. Otherwise if you exceed the headroom voltage of the IDAC, you will not be getting the required current. I just wan to confirm that too.
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
Could you please give more details about the issue? If you could share your project that will be helpful. If you haven't made any changes to the RTD example code, please let us know about your RTD external circuit.
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear vrs,
I am using same example of rtd given in psoc creator . My connection are
also same nothing changed.
For testing of idac I tried running idac8 example . In this example I get
1ma . I verified it using ampmeter. But the rtd example having some weird
issue.Only this example instead of sourcing 1ma it is sourcing 225
microamp only. This makes my rtd reading faulty.
No changes made by me same code same connection only 3 wire rtd is used
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Pratik,
Could you please share your project. In creator go to file -> Create workspace bundle and choose minimal option. Also let me the external circuit diagram of your setup.
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Ok . I am currently not at my desk I will do it asap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
board and device is cy8c5888LTI-LP097
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
The project you have attached is using part number CY8C5868AXI-LP035 , but the device you have posted is CY8C5888LTI-LP097. I just want to know the pins you are using and schematic so that I can test it at my end. That is why the exact project you are using is required. Additionally are you using CY8CKIT-059 for this testing ?
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear VRs,
yes i am using CY8CKIT-059 for my project. Also i re-chosen the device from
device selector CY8C5888LTI-LP097 and then compiled.
Details of pins usage
pins 3.6 and 3.7 are sourcing current.
pins 0.0 and 0.1 are reading rtd similarly pin 0.4 and pin 0.5 are
reading ref resistor.
I was just cross testing the project schematic and found that current mux
not properly working here. will please re check at your end.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Vrs,
This is weird issue. As i have designed and tested many other modules of my
project on this kit59. Some how this code is not working . Also is my 3
wire rtd connection proper. I think it is
On Wed, Sep 5, 2018 at 3:23 PM pratik bhagat <quadratechinfo@gmail.com>
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
From a quick review, can you change pin 0.4 to some other pin( avoid using pins 0.4,0.3,0.2 and 3.2 as they are pins where SAR ADC bypass capacitor is connected). Please let me know whether this solves your issue.
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
no success.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
I have tested the project as per your configuration on CY8CKIT059 kit. I have kept break points during Reference resistor measurement and RTD resistance measurement and I was able to see ~1mA current on both the pins using the multimeter. So the issue at your side might be something else. Could you please tell keep a breakpoint after the IDAC value is set and tell me the voltage at these pins? Your schematic says you are connecting less value resistnaces- so that should not be the issue. Otherwise if you exceed the headroom voltage of the IDAC, you will not be getting the required current. I just wan to confirm that too.
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear vrs,
Thanks for helping me.out.
I followed the said breakpoints and was able to Catch the error.
The ref resistor reading error. Dunno something wrong. I changed the
resistor .
Yes the 1ma current was previously also passing through rtd and ref
resistor and being rapidly switch, and because of this I was not able to
see it on meter.
Thanks a ton problem solved.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pratik,
Happy to know that this worked. Happy designing !
Best Regards,
VRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks and good bless you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content