PSoC™ 4 Forum Discussions
I'd like to use the user SFlash of PSoC 4100S series chips, but I'm not sure if the Trim setting is here too.
Because I see below from "PSoC 4100S - 4100S Plus Architecture TRM.pdf".
Is the SFlash here different from the user SFlash? The starting address of SFlash is 0x0FFFF000, and the starting address of user SFlash is 0x0FFFF200?
Show LessHi folks,
i am new to PSoC and i try to talk via SPI to a communication peripheral hardware. But there are a few type definitions ... missing. I would like to use PDL verion 2.1.0 to implement my interrupts and other things. I tried to include cy_pdl.h to my project, but i got build error: cy_pdl.h not found. In fact cy_pdl.h is in PDL version 3, not in 2. But how to deal with it? How can i speak SPI with PDL in PSoC4.
I found lots of documents, doing it like PSoC6. But PSoC4 needs version 2 ... so i am a little bit confused.
Is there a possibility to use PDL SCP_SPI with PSoC4 or not?
Thx
linuxanton
Show LessHello,
I have touble to download below CY8CKIT-146 development tools, we also bought several CY8CKIT-042 boards, same issue to download corresponding development tools as well. Could you let me know how to get these development tools packages? Thanks.
Show Less
Dear Receiver,
I would like to download older version of PSoC Programmer but I can't find their link address.
I found some historical release note in the following link...
https://www.infineon.com/cms/en/design-support/tools/sdk/psoc-software/
but no corresponding PSoC Programmer versions can be downloaded.
Could you please guide me where to download older version of PSoC Programmer ?!
Thank you so much.
Show Less
Dear Receiver,
Sorry, I really feel confused about kitprog, kitprog_3, and PSOC_programmer.
#In the KitProg3 User Guide you can see...
KitProg3 is the Cypress low-level communication firmware for programming and debugging.
#In the KitProg User Guide you can see...
The KitProg is an onboard programmer/debugger with USB-I2C and USB-UART bridge functionality.
So,,, KitProg3 is a firmware and KitProg is a hardware ?! You also can refer to the attached file.
I really feel confused about what's the role of KitProg, KitProg3 and PSOC_programmer.
Could you provide me a clear definition to the KitProg, KitProg3 and PSOC_programmer ?!
Thank you so much.
Show LessDear Receiver,
I would like to know what's the differences between MiniProg_3 and KitProg_3 !!
I know MiniProg_3 is a discrete device that can program PSoC MCUs.
KitProg_3 is an on board program device that connect to EVM kit. It's an on board programmer or debugger in every EVM kit.
I think these 2 devices are the same. I mean MiniProg_3 = KitProg_3.
So I feel confused, why these 2 devices have different name. Are they different ?!
Besides, could you also guide me what the relationship between "OpenOCD" and MiniProg_3, MiniProg_4, KitProg_3, and Kit_Prog_4 ?! I mean ... Is OpenOCD a software that be built in above programming device ?!
Thank you so much.
Show LessHi,
i'm developing an application on PSoC4 using PSoC Creator. I'd like, if a crash error occurs, try to save the stack and all the most important registers [PC, ecc] in flash to try restore the situation during the problem just to understand what's happened [using the "Call Stack"].
Is it possibile to restore the stack and all the registers with PSoC Creator? If so, which kind of file [extension], should i give to PSoC creator for making it?
Show LessHi.,
Please Help Me in resolving Debugging Issue., When I'm Trying to load project, it's thronging error Like "Project Name Already started Please terminate it and reload"., How can I terminate and Reload it Once again.,
Please Find Bellow attachment for Exact query.,
Thanks
Srikanth
Show LessDear Receiver,
I would like to verify the hex file which is programmed in the PSOC4 flash.
So I need to read the hex file out.
Is there any software tool that can help me to reach this goal ?!
Thank you so much.
Show Lessneed to do this, but be able to do it on multiple pins at same time, not just one. Is there a way I can do this, so I can send my data on all the pins at the same time?
Thanks
Show Less