2 Replies Latest reply on Aug 16, 2017 9:23 AM by jean.boucher_1839961

    Suddenly get "Error: pft.M0101: Unable to generate metadata file:"

    jean.boucher_1839961

      I used to be able to build this simple bootloadable app (Top Design only has a SPI slave, a GPIO input pin, and a Bootloadable component) but all of a sudden I get:

         

      Log file for this session is located at: C:\Users\Jean.Boucher\AppData\Local\Temp\PSoC Creator-000.log
      Warning: Firmware is not fully loaded and device cannot be detected. Please reconnect - "MiniProg3/1614BB00109C".
      --------------- Build Started: 08/14/2017 16:57:28 Project: ManufacturingApp, Configuration: ARM GCC 5.4-2016-q2-update Release ---------------
      cydsfit.exe -.appdatapath "C:\Users\Jean.Boucher\AppData\Local\Cypress Semiconductor\PSoC Creator\4.1" -.fdsnotice -.fdswarpdepfile=warp_dependencies.txt -.fdselabdepfile=elab_dependencies.txt -.fdsbldfile=generated_files.txt -.fdsreffile=referenced_files.txt -p C:\Users\Jean.Boucher\Indigo\rc2.0.0_PSoC_IRQ_Btldr\device\safety\project\ManufacturingApp.cydsn\ManufacturingApp.cyprj -d CY8C5268LTI-LP030 -s C:\Users\Jean.Boucher\Indigo\rc2.0.0_PSoC_IRQ_Btldr\device\safety\project\ManufacturingApp.cydsn\Generated_Source\PSoC5 -- -yv2 -q10 -ygs -o2 -v3 -.fftcfgtype=LE
      Elaborating Design...
      HDL Generation...
      Synthesis...
      Tech Mapping...
      Analog Placement...
      Analog Routing...
      Analog Code Generation...
      Digital Placement...
      Digital Routing...
      Bitstream Generation...
      Error: pft.M0101: Unable to generate metadata file:
      Dependency Generation...
      Cleanup...
      Error: fit.M0050: The fitter aborted due to errors, please address all errors and rebuild. (App=cydsfit)
      --------------- Build Failed: 08/14/2017 16:57:36 ---------------
      --------------- Clean Started: 08/14/2017 16:57:46 Project: ManufacturingApp, Configuration: ARM GCC 5.4-2016-q2-update Release ---------------
      Deleting file ".\ManufacturingApp.rpt"
      --------------- Clean Succeeded: 08/14/2017 16:57:46 ---------------
      --------------- Build Started: 08/14/2017 16:58:14 Project: ManufacturingApp, Configuration: ARM GCC 5.4-2016-q2-update Release ---------------
      cydsfit.exe -.appdatapath "C:\Users\Jean.Boucher\AppData\Local\Cypress Semiconductor\PSoC Creator\4.1" -.fdsnotice -.fdswarpdepfile=warp_dependencies.txt -.fdselabdepfile=elab_dependencies.txt -.fdsbldfile=generated_files.txt -.fdsreffile=referenced_files.txt -p C:\Users\Jean.Boucher\Indigo\rc2.0.0_PSoC_IRQ_Btldr\device\safety\project\ManufacturingApp.cydsn\ManufacturingApp.cyprj -d CY8C5268LTI-LP030 -s C:\Users\Jean.Boucher\Indigo\rc2.0.0_PSoC_IRQ_Btldr\device\safety\project\ManufacturingApp.cydsn\Generated_Source\PSoC5 -- -yv2 -q10 -ygs -o2 -v3 -.fftcfgtype=LE
      Elaborating Design...
      HDL Generation...
      Synthesis...
      Tech Mapping...
      Analog Placement...
      Analog Routing...
      Analog Code Generation...
      Digital Placement...
      Digital Routing...
      Bitstream Generation...
      Error: pft.M0101: Unable to generate metadata file:
      Dependency Generation...
      Cleanup...
      Error: fit.M0050: The fitter aborted due to errors, please address all errors and rebuild. (App=cydsfit)
      --------------- Build Failed: 08/14/2017 16:58:21 ---------------

         

       

         

      Not very helpful error message. Seems like something should follow the ":" at the end of it. I can't figure-out what's suddenly causing this. Updating to PSoC Creator 4.1 Update 1 (4.1.0.3210) didn't help.  Does the same for Debug configuration. Has anyone else seen this error?