2 Replies Latest reply on Jul 20, 2016 3:20 PM by vens

    Murata SN8000/imx6ul Board can not connect to network

    ryan.shuttleworth

      Hello all. 

       

      Sorry, I'm new to this so please bear with me.  I am trying to bring up an SN8000 on a custom i.MX board based on the imx6ul EVK design. I am able to partially bring up the module, scan for (and detect) networks using iw as well as wpa_cli but I can not connect to open or secured networks. Has anyone had experience with the i.mx 6 and SN8000 that can give me advice on bringing up the SN8000 as well as how to better diagnose these connection issues?

       

      Below are examples of boot messages and connection error messages and I have also attached a full trace from the driver using dhd_msg_level=0x2fff

       

      Thanks.

       

      Boot messages

      =============

       

      Power-up adapter 'DHD generic adapter'

      wifi_platform_bus_enumerate device present 1

      F1 signature OK, socitype:0x1 chip:0xa962 rev:0x1 pkg:0x9

      DHD: dongle ram size is set to 245760(orig 245760) at 0x0

      wifi_platform_get_mac_addr

      CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211)

      wl_create_event_handler(): thread:wl_event_handler:d6 started

      CFG80211-ERROR) wl_event_handler : tsk Enter, tsk = 0x88a4141c

      dhd_attach(): thread:dhd_watchdog_thread:d7 started

      dhd_attach(): thread:dhd_dpc:d8 started

      dhd_deferred_work_init: work queue initialized

      dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.

      dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)

      wifi_platform_get_mac_addr

      Firmware up: op_mode=0x0005, MAC=00:0b:6c:41:9b:cd

      dhd_preinit_ioctls buf_key_b4_m4 set failed -23

      Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d

      dhd_preinit_ioctls wl ampdu_hostreorder failed -23

      dhd_wlfc_init(): successfully enabled bdcv2 tlv signaling, 79

      dhd_wlfc_init(): wlfc_mode=0x0, ret=-23

       

      Dongle Host Driver, version 1.141.72 (r)

      Compiled from

      Register interface [wlan0]  MAC: 00:0b:6c:41:9b:cd

       

      CFG80211-ERROR) wl_cfg80211_connect : error (-14)

      CFG80211-ERROR) wl_cfg80211_connect : Connectting withff:ff:ff:ff:ff:ff channel (0) ssid "OUR_SSID", len (17)

       

      CFG80211-ERROR) wl_cfg80211_connect : error (-14)

      CFG80211-ERROR) wl_cfg80211_connect : Connectting withff:ff:ff:ff:ff:ff channel (0) ssid "OUR_SSID", len (17)

       

      CFG80211-ERROR) wl_cfg80211_connect : error (-14)

      CFG80211-ERROR) wl_cfg80211_connect : Connectting withff:ff:ff:ff:ff:ff channel (0) ssid "OUR_SSID", len (17)

       

       

      Note

      ====

       

      I have also seen the following with tracing on i.e. dhd_msg_level=0x2fff

       

      nl80211: Driver does not support authentication/association or connect commands

       

      Attached is an archive of the entire trace session