1 Reply Latest reply on Aug 13, 2015 7:16 PM by 杉林漫漫5

    Error: address + size wrapped(0xfffffffe, 0x00000004)

    杉林漫漫5

      hi ,

        sometime, when I create a timer event by wiced_rtos_register_timed_event() function,an error appear in the openocd_log.txt file. but I delete the timer event ,the error disappear. Which reasons could cause this problem ?? in SDK 3.1.2,  platform BCM9WCDUSI09

       

      Info : only one transport option; autoselect 'jtag'

      trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain connect_deassert_srst

      adapter speed: 1000 kHz

      adapter_nsrst_delay: 100

      jtag_ntrst_delay: 100

      Warn : target name is deprecated use: 'cortex_m'

      jtag_init

      Info : J-Link initialization started / target CPU reset initiated

      Info : J-Link V9 compiled Oct 28 2014 19:25:34

      Info : J-Link caps 0xb9ff7bbf

      Info : J-Link hw version 90000

      Info : J-Link hw type J-Link

      Info : J-Link max mem block 71184

      Info : J-Link configuration

      Info : USB-Address: 0x0

      Info : Kickstart power on JTAG-pin 19: 0xffffffff

      Info : Vref = 3.304 TCK = 1 TDI = 0 TDO = 0 TMS = 0 SRST = 0 TRST = 0

      Info : J-Link JTAG Interface ready

      Info : clock speed 1000 kHz

      Polling target stm32f2xxx.cpu failed, GDB will be halted. Polling again in 100ms

      Info : JTAG tap: stm32f2xxx.cpu tap/device found: 0x4ba00477 (mfg: 0x23b, part: 0xba00, ver: 0x4)

      Info : JTAG tap: stm32f2xxx.bs tap/device found: 0x06411041 (mfg: 0x020, part: 0x6411, ver: 0x0)

      Info : Selecting JTAG transport command set.

      Info : AP INIT COMPLETE

      Info : stm32f2xxx.cpu: hardware has 6 breakpoints, 4 watchpoints

      Info : JTAG tap: stm32f2xxx.cpu tap/device found: 0x4ba00477 (mfg: 0x23b, part: 0xba00, ver: 0x4)

      Info : JTAG tap: stm32f2xxx.bs tap/device found: 0x06411041 (mfg: 0x020, part: 0x6411, ver: 0x0)

      Info : Selecting JTAG transport command set.

      Info : AP INIT COMPLETE

      Polling target stm32f2xxx.cpu succeeded again

      Info : Selecting JTAG transport command set.

      Info : AP INIT COMPLETE

      Info : accepting 'gdb' connection from 3333

      Info : device id = 0x20036411

      Info : flash size = 1024kbytes

      Warn : acknowledgment received, but no packet pending

      Info : Auto-detected RTOS: ThreadX

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Warn : stepi ignored. GDB will now fetch the register state from the target.

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: Not implemented: target_get_gdb_fileio_info_default

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: Not implemented: target_get_gdb_fileio_info_default

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)

      Error: address + size wrapped(0xfffffffe, 0x00000004)