Read protect of Configuration Table

Announcements

Live Webinar: USB-C adoption. Simple & Cost-efficient solutions | April 18th @9am or 5pm CEST. Register now !

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
KeTa_1341526
Level 5
Level 5
Distributor - TED (Japan)
10 likes given 10 likes received 5 likes given

Hello,

Can I make [User Parameter] of EZ-PD Configuration Utility unreadable?

The designer uses the EZ-PD Configuration Utility to write any user information to [User Parameter].

So, [User Parameter] is information that the user wants to keep confidential to other companies.

After writing [User Parameter], manipulate some flags to prevent this setting data from being read, or mask the data (All 0).

Is that possible?

Best regards,

Kenji

0 Likes
1 Solution

As a matter of fact that devices cannot protect any sniffering from strangers.

In this case as well, there is a possibility that strangers sniffer the parameters.

はい。あいにくですが、想定されているようなことも起こる可能性があり、絶対に防ぐことは不可能です。

今回いただいた要求を元に保護機能の実装を社内でリクエストしますが、2019年現在、この機能はないことをご理解いただけますと幸いです。

Best regards,

Hirotaka Takayama

View solution in original post

0 Likes
5 Replies
HirotakaT_91
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

I am afraid that EZ-PD Configuration Utility does not have data protection feature.

You can program all the information of EZ-PD Configuration Utility to the FW. Then, they can provide only the programmed device or only hex file to the other company. This procedure is help to protect the information of being set on the EZ-PD Configuration Utility.

Best regards,

Hirotaka Takayama

0 Likes
KeTa_1341526
Level 5
Level 5
Distributor - TED (Japan)
10 likes given 10 likes received 5 likes given

I will ask you questions in Japanese.

回答としては、EZ-PD Configuration UtilityのUser Parameterをマスクする機能は無いという事で宜しいでしょうか?

Best Regards,

Kenji Takahashi

0 Likes

You are right. As a result, there is no way to mask parameters for EZ-PD Configuration Utility.

Consequently, I mentioned following way to you earlier.

"You can program all the information of EZ-PD Configuration Utility to the FW. Then, they can provide only the programmed device or only FW hex file to the other company. This procedure is help to protect the information of being set on the EZ-PD Configuration Utility."

Japanese: EZ-PD Configuration Utilityにパラメータをマスクする機能はありません。

Best regards,

Hirotaka Takayama

0 Likes
KeTa_1341526
Level 5
Level 5
Distributor - TED (Japan)
10 likes given 10 likes received 5 likes given

For this device, CC boot-loader  is programmed.

Even if a FW with a user parameter set is written, isn't it possible to read the user parameter with EZ-PD Configuration?

Japanese: 実はこのデバイスに、CC Boot-loaderが書き込まれています。(これはカスタムFWです。)

     その為、FWにUser parameterを設定しても、CCからEZ-PD Configuration Utilityで中の設定データは分かってしまうのでは

     ないでしょうか?

Best Regards,

Kenji Takahashi

0 Likes

As a matter of fact that devices cannot protect any sniffering from strangers.

In this case as well, there is a possibility that strangers sniffer the parameters.

はい。あいにくですが、想定されているようなことも起こる可能性があり、絶対に防ぐことは不可能です。

今回いただいた要求を元に保護機能の実装を社内でリクエストしますが、2019年現在、この機能はないことをご理解いただけますと幸いです。

Best regards,

Hirotaka Takayama

0 Likes