Please download and install PSoC Programmer (the newest one is recommended) from the URL below.
Stop debugger of PSoC Creator if it is running to avoid connection conflict.
Connect your board to PC and startup PSoC Programmer
Then select "Utilities" tab and select "Upgrade Firmware"
When the bottom green bar shows "PASS" and the Results said Succeeded, it's done.
Please quit PSoC Programmer and keep on what you were doing.
I'm sorry for hearing that my suggestion did not work.
BTW, are you still receiving same error message?
> "KitProg2 version Expecting 1.05, but found 1.02. Please use PSoC Programmer GUI to upgrade firmware"
Or are you getting different error message now?
If so would you post the exact error message you are getting?
This error message is solved but not the gui capsense tuner is not getting
connected to the kit when i am launching the tuner, the i2c bridge is not
I am getting the message unable to receive the data from the device.
On Fri, Nov 15, 2019 at 1:46 PM Motoo Tanaka <firstname.lastname@example.org>
Also in the literature it is suggesting that kitprog2 is supported but i am using kitprog3 will that effect?
It was my bad that I thought it was PSoC 4100S Plus kit (CY8CKIT-149)
but you are using CY8CKIT-041-41XX PSoC 4100S Pioneer Kit, right?
Then as I don't have that board all I can do is suggesting "usual" check ups.
I think that the kit has on board KitProg2.
Are you using an external KitProg3
or have you updated the KitProg firmware to KitProg3,
or are you using an external MiniProg3?
Could you check
(1) Pin assign
I2C_SDA : P3_1
I2C_SCL : P3_0
(2) The program is compiled without error
(3) The program is programmed to the device without error
(4) Then you are following the operation in the Schematic
One mire problem i am facing is that when i am building and programming the
device with one button example code. I am not getting any change in value
when i am connecting a wire to P and it blinking only when i am touching
the base of p header. How can i change the baseline header.
On Fri, Nov 15, 2019 at 2:46 PM Shivam Trivedi <email@example.com>
One thing I noticed is that legacy PSoC 4 and PSoC 4100S / 4100S Plus are somewhat different.
So how about trying sample for PSoC 4100S?
I'm assuming that you are using CY8CKIT-041-41XX, if not please replace the kit name with what you are using.
At first go to Kit's page
Scroll down to resource listing...
And please select and download CY8CKIT-041-41XX PSOC 4100S PIONEER KIT Complete Setup
Then open the CY8CKIT04141XXSetup_RevSA.exe file as an admin.
In the Product Installation Overview page, select "Complete" and select [Next >]
Read License Agreement and accept if you agree and select [Next >]
When installation is done, you should have sample project in
C:\Program Files (x86)\Cypress\CY8CKIT-041-41XX PSoC 4100S Pioneer Kit\1.0\Firmware\PSoC 4100S
Please try project in this folder.
Hi i am using PSOC 4100S PIONEER KIT to implement and test a linear slider example. Please let me know if you know of any example that is developed for this particular kit. At present i am programming the device with linear slider example developed for 042 kit and i am changing the device from device selector in projects menu to my device i.e cy8c4146azis433 still it is not working. Please tell if i am doing any mistake.
2 of 2 people found this helpful
1. Please check if you are using the correct I2C pins. Let us know what pins you have connected them to.
2. Check if your ezi2c component is configured as below:
Send us screenshots of all the error messages you observe in Tuner GUI.
Also make sure none of the other software such as PSoC programmer, BCP are running at the background. There are chances that you're device is connected to the other software. Please close all other instances and make sure only Tuner GUI and PSoC Creator is running.
At present i am programming the device with linear slider example developed for 042 kit and i am changing the device from device selector in projects menu to my device i.e cy8c4146azis433 still it is not working.
Could you please let us know what is not working? It will be really helpful if you could tell us which part is not working (Tuner, programming, CapSense performance etc)so that it will be easy for us to debug the issue.
Hi thanks for your response, the device got connected to the tuner gui and slider is working. The main issue was I2c which is configured correctly now.
Now second task i want to tune the slider graph view as per my application i.e to control the brightness of led also the status is 1 always can you tell me why it is happening.
The slider is not working with an overlay. Please tell how should i change the settings so that the slider works with an overlay above it.