1 Reply Latest reply on Dec 16, 2019 1:40 AM by HongyanW_86

    Chip erasing issue on CYT2B75CAS using JLink

    aaha_4508176

      Hi,


      I have an issue flashing the CYT2B75CAS using JLink commander similar to this issue.

      Flashing Issue CYT2B75CAE

       

      I can connect, read memory sections, write to memory sections read and write register etc
      However when I attempt an erase I get a `Failed to execute RAMCode for chip erase!` error

       

      Below is the command line trace:

       

       

      $ jlink -device CYT2B75BAS_M4 -speed 1000 -if JTAG -autoconnect 1
      SEGGER J-Link Commander V6.48b (Compiled Aug  2 2019 10:19:19)
      DLL version V6.48b, compiled Aug  2 2019 10:18:25
      
      Connecting to J-Link via USB...O.K.
      Firmware: Silicon Labs J-Link Pro OB compiled May 16 2019 11:50:55
      Hardware version: V4.00
      S/N: 440092275
      License(s): RDI
      IP-Addr: DHCP (no addr. received yet)
      VTref=3.331V
      Device position in JTAG chain (IRPre,DRPre) <Default>: -1,-1 => Auto-detect
      JTAGConf>
      Device "CYT2B75BAS_M4" selected.
      
      
      Connecting to target via JTAG
      ConfigTargetSettings() start
      J-Link script: ConfigTargetSettings()
      ConfigTargetSettings() end
      TotalIRLen = 8, IRPrint = 0x0011
      JTAG chain detection found 2 devices:
      #0 Id: 0x6BA00477, IRLen: 04, CoreSight JTAG-DP
      #1 Id: 0x2E300069, IRLen: 04, Unknown device
      AP map detection skipped. Manually configured AP map found.
      AP[0]: APB-AP (IDR: Not set)
      AP[1]: AHB-AP (IDR: Not set)
      AP[2]: AHB-AP (IDR: Not set)
      AP[2]: Core found
      AP[2]: AHB-AP ROM base: 0xE00FF000
      CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
      Found Cortex-M4 r0p1, Little endian.
      FPUnit: 6 code (BP) slots and 2 literal slots
      CoreSight components:
      ROMTbl[0] @ E00FF000
      ROMTbl[0][0]: E0080000, CID: B105900D, PID: 005BB906 CTI
      ROMTbl[0][1]: E008C000, CID: B105900D, PID: 003BB908 CSTF
      ROMTbl[0][2]: E008D000, CID: B105900D, PID: 004BB907 ETB
      ROMTbl[0][3]: E008E000, CID: B105900D, PID: 003BB923 TPIU-Lite
      ROMTbl[0][4]: E007F000, CID: B105100D, PID: 102B4101 ROM Table
      ROMTbl[1] @ E007F000
      ROMTbl[1][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
      ROMTbl[1][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
      ROMTbl[1][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
      ROMTbl[1][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
      ROMTbl[1][4]: E0042000, CID: B105900D, PID: 005BB906 CTI
      ROMTbl[1][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
      Cortex-M4 identified.
      J-Link>erase
      Erasing device...
      
      ****** Error: Timeout while erasing chip, RAMCode did not respond in time. (PC = 0x4115709B, CPSR = 0xC34BA592, LR = 0x56996DFE)!
      Failed to erase chip.
      Failed to execute RAMCode for chip erase!
      J-Link: Flash download: Total time needed: 20.118s (Prepare: 0.082s, Compare: 0.000s, Erase: 20.019s, Program: 0.000s, Verify: 0.000s, Restore: 0.016s)
      ERROR: Erase returned with error code -5.
      

       

      I've tried the latest JLinkARM.dll v6.52 but the same message occurs. Any Ideas why this might be happening?

       

      I've attached the log of the erase command

       

      Thanks