- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I am trying to download code (e.g. snip.scan-CYW943907AEVAL1F download run) on CYW943907AEVAL1F eval board connected through USB but it fails during 'build apps lookup table'.
This used to work with earlier WICED versions 5.x but now it fails with latest WICED 6.2.
The user manual for CYW943907AEVAL1F eval board (https://www.cypress.com/file/370526/download ) says the device should comes up as :
1. The WICED USB Serial Port is listed under Ports (COM & LPT) as shown in Figure 3-3. b.
2. The WICED USB JTAG Port is listed under WICED USB JTAG Devices as shown in Figure 3-3.
It used to come up with earlier versions like this. But with new version, it shows up for #2 as 'libusb-win32 devices' instead of 'WICED USB JTAG devices'.
I tried re-installing device driver but no luck, and shows up as same.
Please help on how to correct this error to be able to flash over USB OR it will work only with previous versions only.
Thanks.
-Vikas.
Console:
Building apps lookup table
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:372: recipe for target 'download_dct' failed
make.exe[1]: *** [download_dct] Error 1
Makefile:351: recipe for target 'main_app' failed
make: *** [main_app] Error 2
OpenOCD log:
Open On-Chip Debugger 0.10.0+dev-00227-g0d15c62 (2018-03-27-15:19)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
trst_and_srst separate srst_nogate trst_push_pull srst_open_drain connect_assert_srst
trst_and_srst separate srst_nogate trst_push_pull srst_open_drain connect_assert_srst
adapter speed: 100 kHz
adapter_nsrst_delay: 100
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
jtag_ntrst_delay: 100
post_init_psoc6_setup
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Info : clock speed 100 kHz
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
Info : BCM43909.cpu: hardware has 4 breakpoints, 4 watchpoints
in procedure 'sflash_write_file'
in procedure 'sflash_init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 261
in procedure 'init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 155
in procedure 'ocd_bouncer'
force hard breakpoints
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
Error: Error BCM43909.cpu: Reset was not successfully asserted
in procedure 'sflash_write_file'
in procedure 'sflash_init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 261
in procedure 'post_init_43909_setup' called at file "apps/waf/sflash_write/sflash_write.tcl", line 160
in procedure 'reset' called at file "apps/waf/sflash_write/sflash_write.tcl", line 569
in procedure 'ocd_bouncer'
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Raktim Roy wrote:
The compilation passes in my system; not sure why it fails for you. I am adding the BSP and gpio_button library here for you to re-check.
This is because your sdk is different from the public sdk-6.2.1.
gpio_button_t does not has the member named 'config'.
And below changes just shows current public sdk-6.2.1 has bug in gpio_button.
if ( button->trigger == 0 )
{
- trigger = ( ( button->polarity == WICED_ACTIVE_LOW ) ? IRQ_TRIGGER_RISING_EDGE : IRQ_TRIGGER_FALLING_EDGE );
+ /* if trigger has not been defined for the platform, choose based on button polarity */
+ trigger = ( ( button->polarity == WICED_ACTIVE_LOW ) ? IRQ_TRIGGER_FALLING_EDGE : IRQ_TRIGGER_RISING_EDGE );
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The drivers have been updated post SDK 6.1 release. Please check this help article Upgrade USB Drivers for WICED Studio 6.1 for further information
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Updated the driver and its showing up as 'libusbk' but still code will not load.
Showing same error:
Console log:
Creating Filesystem BCM94390x_targets.mk ...
Downloading DCT ... build/snip.scan-CYW943907AEVAL1F/DCT.bin @ SFLASH_DCT_LOC=0x00008000
./tools/common/Win32/mk_wicedfs32 build/snip.scan-CYW943907AEVAL1F/filesystem.bin build/snip.scan-CYW943907AEVAL1F/resources/Staging/
Creating Filesystem Done
Building apps lookup table
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:372: recipe for target 'download_dct' failed
make.exe[1]: *** [download_dct] Error 1
Makefile:351: recipe for target 'main_app' failed
make: *** [main_app] Error 2
09:27:18 Build Finished (took 4s.822ms)
OpenOCD log:
Open On-Chip Debugger 0.10.0+dev-00227-g0d15c62 (2018-03-27-15:19)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
trst_and_srst separate srst_nogate trst_push_pull srst_open_drain connect_assert_srst
trst_and_srst separate srst_nogate trst_push_pull srst_open_drain connect_assert_srst
adapter speed: 100 kHz
adapter_nsrst_delay: 100
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
jtag_ntrst_delay: 100
post_init_psoc6_setup
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Info : clock speed 100 kHz
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
Info : BCM43909.cpu: hardware has 4 breakpoints, 4 watchpoints
in procedure 'sflash_write_file'
in procedure 'sflash_init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 261
in procedure 'init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 155
in procedure 'ocd_bouncer'
force hard breakpoints
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
Error: Error BCM43909.cpu: Reset was not successfully asserted
in procedure 'sflash_write_file'
in procedure 'sflash_init' called at file "apps/waf/sflash_write/sflash_write.tcl", line 261
in procedure 'post_init_43909_setup' called at file "apps/waf/sflash_write/sflash_write.tcl", line 160
in procedure 'reset' called at file "apps/waf/sflash_write/sflash_write.tcl", line 569
in procedure 'ocd_bouncer'
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Can you confirm that the same EVK works with 5.1 SDK and does not work with 6.2 SDK?
Can you please provide the device manager screenshot?
From the openocd log, it seems to be a driver issue only. Please make sure to do a hard reset and clean before downloading the new target.
./make clean
./make snip.scan-CYW943907AEVAL1F WIPE=1 download run
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes, same EVK is working with WICED STUDIO SDK 4.0. I upgraded system to Windows 10 - and couldn't find WICED 5.0 setup online but found WICED 4.0 setup online so used that one and it is working with that.
snip.scan-BCM943907AEVAL2F download run
I did following:
- From WICED 6.2, ./make clean - pass
- From WICED 6.2, ./make snip.scan-CYW943907AEVAL1F WIPE=1 download run - fail as compiled fine but no output on UART.
- From WICED 6.2, ./make snip.scan-CYW943907AEVAL1F download run - fail as compiled fine but no output on UART.
- Hard reset.
- From WICED 6.2, ./make clean - pass
- From WICED 6.2, ./make snip.scan-CYW943907AEVAL1F WIPE=1 download run - fail as compiled fine but no output on UART.
- From WICED 6.2, ./make snip.scan-CYW943907AEVAL1F download run - fail as compiled fine but no output on UART.
- From WICED 4.0, ./make snip.scan-BCM943907AEVAL2F download run - pass as compiled fine and output on UART.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
From your log, it looks like that you have a different revision of the kit (BCM943907AEVAL2F instead of the latest and greatest CYW943907AEVAL1F). Please confirm whether this assumption is wrong? If the assumption is correct, then can you port the platform files for BCM943907AEVAL2F in the WICED 6.2 and then try?
Also I can see that the download_dct error is gone but instead the uart debug prints are missing now? Please confirm whether that is correct
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The board says "121-90484-01 rev04 1735EM00153" on its label.
With WICED 4, it has worked with BCM943907AEVAL2F only, there is no CYW943907AEVAL1F in platform.
With WICED 5, it was working with CYW943907AEVAL1F.
YES, there is no download_dct error but UART not working.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please use the attached platform files and check the uart issue first. After adding the BSP in 43xxx_Wi-Fi/platforms, your make target should look like
./make snip.scan-BCM943907AEVAL2F download run
To debug further, open the waf.sflash_write.c and take DEBUG_PRINT out of the commented section and check whether you are seeing anything in the serial terminal.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
It didn't compile.
Console log:
MAKEFILE MAKECMDGOALS=snip.scan-BCM943907AEVAL2F download run OTA2_SUPPORT is disabled
Making config file for first time
+-----------------------------------------------------------------------------------------------------+
| IMPORTANT NOTES |
+-----------------------------------------------------------------------------------------------------+
| Wi-Fi MAC Address |
| The target Wi-Fi MAC address is defined in <WICED-SDK>/generated_mac_address.txt |
| Ensure each target device has a unique address. |
+-----------------------------------------------------------------------------------------------------+
| MCU & Wi-Fi Power Save |
| It is *critical* that applications using WICED Powersave API functions connect an accurate 32kHz |
| reference clock to the sleep clock input pin of the WLAN chip. Please read the WICED Powersave |
| Application Note located in the documentation directory if you plan to use powersave features. |
+-----------------------------------------------------------------------------------------------------+
MAKEFILE MAKECMDGOALS=snip.scan-BCM943907AEVAL2F download run OTA2_SUPPORT is disabled
Building Bootloader waf.bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909
Building Tiny Bootloader waf.tiny_bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909
Building Serial Flash Loader App
platforms/BCM943907AEVAL2F/platform.c:289:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c:297:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_init_external_devices':
platforms/BCM943907AEVAL2F/platform.c:336:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_1].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_1].config );
^
platforms/BCM943907AEVAL2F/platform.c:337:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_2].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_2].config );
^
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_get_button_press_time':
platforms/BCM943907AEVAL2F/platform.c:353:96: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ button_gpio ], platform_gpio_buttons[button_index].config );
^
make.exe[3]: *** [build/waf.bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909/Modules/platforms/BCM943907AEVAL2F/platform.o] Error 1
make.exe[3]: *** Waiting for unfinished jobs....
make.exe[2]: *** [main_app] Error 2
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:260: recipe for target 'bootloader' failed
make.exe[1]: *** [bootloader] Error 2
make.exe[1]: *** Waiting for unfinished jobs....
platforms/BCM943907AEVAL2F/platform.c:289:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c:297:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_init_external_devices':
platforms/BCM943907AEVAL2F/platform.c:336:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_1].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_1].config );
^
platforms/BCM943907AEVAL2F/platform.c:337:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_2].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_2].config );
^
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_get_button_press_time':
platforms/BCM943907AEVAL2F/platform.c:353:96: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ button_gpio ], platform_gpio_buttons[button_index].config );
^
make.exe[3]: *** [build/waf.tiny_bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909/Modules/platforms/BCM943907AEVAL2F/platform.o] Error 1
make.exe[3]: *** Waiting for unfinished jobs....
make.exe[2]: *** [main_app] Error 2
make.exe[1]: *** [build/snip.scan-BCM943907AEVAL2F/tiny_bootloader_bin2c.o] Error 2
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:227: recipe for target 'build/snip.scan-BCM943907AEVAL2F/tiny_bootloader_bin2c.o' failed
platforms/BCM943907AEVAL2F/platform.c:289:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c:297:10: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
.config = INPUT_PULL_UP, /* No pull up BCM943907AEVAL2F - No physical Buttons, mapped to PWM_5 and SPI0 on the expansion header J6 */
^~~~~~
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_init_external_devices':
platforms/BCM943907AEVAL2F/platform.c:336:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_1].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_1].config );
^
platforms/BCM943907AEVAL2F/platform.c:337:135: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ platform_gpio_buttons[PLATFORM_BUTTON_2].gpio ], platform_gpio_buttons[PLATFORM_BUTTON_2].config );
^
platforms/BCM943907AEVAL2F/platform.c: In function 'platform_get_button_press_time':
platforms/BCM943907AEVAL2F/platform.c:353:96: error: 'gpio_button_t {aka const struct <anonymous>}' has no member named 'config'
platform_gpio_init( &platform_gpio_pins[ button_gpio ], platform_gpio_buttons[button_index].config );
^
make.exe[3]: *** [build/waf.sflash_write-NoOS-BCM943907AEVAL2F-P103-SoC.43909/Modules/platforms/BCM943907AEVAL2F/platform.o] Error 1
make.exe[3]: *** Waiting for unfinished jobs....
make.exe[2]: *** [main_app] Error 2
make.exe[1]: *** [sflash_write_app] Error 2
tools/makefiles/wiced_apps.mk:415: recipe for target 'sflash_write_app' failed
make: *** [main_app] Error 2
Makefile:351: recipe for target 'main_app' failed
14:12:42 Build Finished (took 16s.466ms)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The compilation passes in my system; not sure why it fails for you. I am adding the BSP and gpio_button library here for you to re-check.
Steps to be followed to re-check:
- Place the BSP (BCM943907AEVAL2F) folder in 43xxx_Wi-Fi/platforms
- Kindly place the button library in 43xxx_Wi-Fi/libraries/inputs/gpio_button
- Perform a clean by using ./make clean
- Then try running the make target and check for compilation error: ./make snip.scan-BCM943907AEVAL2F
- Please try to check for uart debug prints by enabling #define DEBUG_PRINT in 43xxx_Wi-Fi/apps/waf/sflash_write/sflash_write.c and see whether you are getting any uart prints during the download process.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Raktim Roy wrote:
The compilation passes in my system; not sure why it fails for you. I am adding the BSP and gpio_button library here for you to re-check.
This is because your sdk is different from the public sdk-6.2.1.
gpio_button_t does not has the member named 'config'.
And below changes just shows current public sdk-6.2.1 has bug in gpio_button.
if ( button->trigger == 0 )
{
- trigger = ( ( button->polarity == WICED_ACTIVE_LOW ) ? IRQ_TRIGGER_RISING_EDGE : IRQ_TRIGGER_FALLING_EDGE );
+ /* if trigger has not been defined for the platform, choose based on button polarity */
+ trigger = ( ( button->polarity == WICED_ACTIVE_LOW ) ? IRQ_TRIGGER_FALLING_EDGE : IRQ_TRIGGER_RISING_EDGE );
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
With this mod in button file and other platform files, eval board is now working with WICED.
Thanks.
-Vikas.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Have you been able to get it working following the last set of instructions?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Adding new platform files, it keeps failing to download dct.
snip.scan-BCM943907AEVAL2F download run
MAKEFILE MAKECMDGOALS=snip.scan-BCM943907AEVAL2F download run OTA2_SUPPORT is disabled
Making config file for first time
+-----------------------------------------------------------------------------------------------------+
| IMPORTANT NOTES |
+-----------------------------------------------------------------------------------------------------+
| Wi-Fi MAC Address |
| The target Wi-Fi MAC address is defined in <WICED-SDK>/generated_mac_address.txt |
| Ensure each target device has a unique address. |
+-----------------------------------------------------------------------------------------------------+
| MCU & Wi-Fi Power Save |
| It is *critical* that applications using WICED Powersave API functions connect an accurate 32kHz |
| reference clock to the sleep clock input pin of the WLAN chip. Please read the WICED Powersave |
| Application Note located in the documentation directory if you plan to use powersave features. |
+-----------------------------------------------------------------------------------------------------+
MAKEFILE MAKECMDGOALS=snip.scan-BCM943907AEVAL2F download run OTA2_SUPPORT is disabled
Building Bootloader waf.bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909
Building Tiny Bootloader waf.tiny_bootloader-NoOS-NoNS-BCM943907AEVAL2F-P103-SoC.43909
Building Serial Flash Loader App
prgm hdr cnt=3
total_size = 13600, entry_point = 0x696000
Loadsegment_offset = 0xA0 segment_size = 13428, segment_pad = 0
Loadsegment_offset = 0x3520 segment_size = 32, segment_pad = 0
Loadsegment_offset = 0x3544 segment_size = 140, segment_pad = 0
Finished Building Bootloader
Processing resources
Creating security credentials
Finished Building Tiny Bootloader
Making DCT image
Compiling App_Scan
Compiling Platform_BCM943907AEVAL2F_P103_B1
Compiling WICED
Finished Building Serial Flash Loader App
Compiling WWD_ThreadX_Interface
Compiling WICED_ThreadX_Interface
Compiling WWD_for_SoC.43909_ThreadX
Compiling Supplicant_BESL
Compiling Lib_DNS
Compiling NetX_Duo
Compiling Lib_Wiced_RO_FS
Compiling MCU_BCM4390x
Compiling Lib_TLV
Compiling Lib_base64
Compiling Lib_Linked_List
Compiling Lib_mbedTLS
Compiling WWD_NetX_Duo_Interface
Compiling WICED_NetX_Duo_Interface
Compiling Lib_crc
Compiling Lib_GPIO_button
Compiling common_GCC
Compiling 43909_Peripheral_Drivers
Compiling Lib_Ring_Buffer
Compiling Lib_DHCP_Server
Compiling SPI_Flash_43909_Library_BCM943907AEVAL2F
Compiling Uart_43909_Library_BCM943907AEVAL2F
Compiling Peripherals_Shared_43909_Library_BCM943907AEVAL2F
Compiling Tiny_Crypto_43909_Library_BCM943907AEVAL2F
Making build/snip.scan-BCM943907AEVAL2F/libraries/App_Scan.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Platform_BCM943907AEVAL2F_P103_B1.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WICED.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WWD_ThreadX_Interface.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WICED_ThreadX_Interface.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WWD_for_SoC.43909_ThreadX.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Supplicant_BESL.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_DNS.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/NetX_Duo.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_Wiced_RO_FS.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/MCU_BCM4390x.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_TLV.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_base64.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_Linked_List.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_mbedTLS.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WWD_NetX_Duo_Interface.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/WICED_NetX_Duo_Interface.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_crc.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_GPIO_button.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/43909_Peripheral_Drivers.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/common_GCC.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_Ring_Buffer.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Lib_DHCP_Server.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/SPI_Flash_43909_Library_BCM943907AEVAL2F.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Uart_43909_Library_BCM943907AEVAL2F.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Tiny_Crypto_43909_Library_BCM943907AEVAL2F.a
Making build/snip.scan-BCM943907AEVAL2F/libraries/Peripherals_Shared_43909_Library_BCM943907AEVAL2F.a
Making snip.scan-BCM943907AEVAL2F.elf
Making snip.scan-BCM943907AEVAL2F.bin
snip.scan-BCM943907AEVAL2F
----------------------------------|---------|
| Static |
Module | RAM |
----------------------------------+---------|
App | 470 |
crc | 1060 |
Interrupt Vectors | 288 |
libc | 28737 |
Networking | 10271 |
NetX-Duo - Interfaces & Stacks | 16 |
NVRam | 2210 |
Other | 59273 |
Packet Buffers | 22928 |
platform | 572 |
RAM Initialisation | 0 |
resources | 32 |
Ring_Buffer | 140 |
Startup Stack & Link Script fill | 171 |
ThreadX | 12220 |
TLV | 28 |
WICED | 5241 |
Wiced_RO_FS | 570 |
WWD | 1413 |
----------------------------------+---------|
TOTAL (bytes) | 145640 |
----------------------------------|---------|
Creating Filesystem BCM94390x_targets.mk ...
Downloading DCT ... build/snip.scan-BCM943907AEVAL2F/DCT.bin @ SFLASH_DCT_LOC=0x00008000
./tools/common/Win32/mk_wicedfs32 build/snip.scan-BCM943907AEVAL2F/filesystem.bin build/snip.scan-BCM943907AEVAL2F/resources/Staging/
Creating Filesystem Done
Building apps lookup table
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:340: recipe for target 'download_dct' failed
make.exe[1]: *** [download_dct] Error 1
Makefile:349: recipe for target 'main_app' failed
make: *** [main_app] Error 2
17:36:20 Build Finished (took 1m:32s.252ms)