- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello.
With this article https://community.cypress.com/community/wiced-wifi/wiced-wifi-forums/blog/2018/03/19/downloading-and... I can to program CYW943907AEVAL1F Board with J-Link. I try do this with my custom board and same Flash Memory, but with failed result.
However, with J-Flash utility I can erase, read and write to flash memory. Does entire hex file exist in Wiced Studio? So I can write it with J-Flash utility.
Log info from openocd_log.txt
Open On-Chip Debugger 0.10.0+dev-00227-g0d15c62 (2018-03-27-15:19)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
trst_and_srst separate srst_nogate trst_push_pull srst_push_pull connect_assert_srst
adapter speed: 100 kHz
adapter_nsrst_delay: 100
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
jtag_ntrst_delay: 100
post_init_psoc6_setup
Warn : Failed to open device: LIBUSB_ERROR_NOT_SUPPORTED.
Info : J-Link V9 compiled Oct 25 2018 11:46:07
Info : Hardware version: 9.40
Info : VTarget = 3.288 V
Info : clock speed 100 kHz
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
Info : BCM43909.cpu: hardware has 4 breakpoints, 4 watchpoints
force hard breakpoints
Info : JTAG tap: BCM43909.cpu tap/device found: 0x5ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x5)
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0x000001f3 pc: 0x00000000
D-Cache: disabled, I-Cache: disabled
cortex_a interrupt mask on
adapter speed: 10000 kHz
cpsr (/32): 0x000000D3
lr (/32): 0x00000000
32796 bytes written at address 0x004a0000
43264 bytes written at address 0x004a8040
32 bytes written at address 0x004b2940
2876 bytes written at address 0x004b2960
downloaded 78968 bytes in 1.459851s (52.825 KiB/s)
entry_address= 4882496
stack_address= 4939032
buffer_size= 32768
pc (/32): 0x004A8040
Total write size is 8000.
writing 8000 bytes at 32768
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0x200000f3 pc: 0x004a8fee
D-Cache: enabled, I-Cache: enabled
loadimage address 4849692 foffset 0 8000
8000 bytes written at address 0x004a001c
downloaded 8000 bytes in 0.148978s (52.441 KiB/s)
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0x200000f3 pc: 0x004a9032
D-Cache: enabled, I-Cache: enabled
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0x200000f3 pc: 0x004a8fee
D-Cache: enabled, I-Cache: enabled
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0x200000f3 pc: 0x004a8ff0
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Problem resolved. RF_SW_CTRL_7(RSRC_INIT_MODE) pin was pull up on my custom board (on CYW943907AEVAL1F it not connected).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please refer this blog WICED application framework and manufacturing image in CYW943907AEVAL1F for details of the WICED framework.
As mentioned in the blog, you need to write the individual binaries at the correct addresses using J-Flash utility. can you please tell me the make target you are using for programming your custom board?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
User.my_project_name-FreeRTOS-LwIP-CYW943907AEVAL1F JTAG=jlink download run
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Can you please try with the latest SDK? The steps are mentioned in this blog Downloading through Jlink Segger in WICED SDK 6.2 and future releases
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Problem resolved. RF_SW_CTRL_7(RSRC_INIT_MODE) pin was pull up on my custom board (on CYW943907AEVAL1F it not connected).