WLAN CYW954907AEVAL1F_Evaluation_Kit testing

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
Anonymous
Not applicable

Hi,

Actually I bought CYW954907AEVAL1F_Evaluation_Kit to test the RF parameters .I am new to WLAN testing .Could you please suggest me to understand and testing/measure the RF parameters.

Thanks,

harshini

0 Likes
1 Solution
RaktimR_11
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

Please check this thread WLAN RF testing which should help you in understanding the basics of RF testing part.

View solution in original post

0 Likes
9 Replies
RaktimR_11
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

Please check this thread WLAN RF testing which should help you in understanding the basics of RF testing part.

0 Likes
Anonymous
Not applicable

Hi,

I want to test the kit(CYW954907EVAL 1F) WLAN 802.11n @40MHz bandwidth, if i change the commands as mentioned below also i'm not able to get 40MHz bandwidth for 5G/2.4G bands.Could you please help me how to set the commands

>> wl43909B0 --serial 8 band b --> b = 2.4 GHz, a = 5 GHz

>> wl43909B0 --serial 8 2g_rate -h MCS7 -b 40 --> 2g = 2.4 GHz, 5g = 5 GHz, -h = MCS0-MCS7, -b = 40 MHz bandwidth

Thanks&Regards,

harshini

0 Likes
Anonymous
Not applicable

Could you please help me for the above request

Thanks&Regards,

harshini

0 Likes
lock attach
Attachments are accessible only for community members.
RaktimR_11
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

Please use the attached batch file which lists out the command sequence for 40MHz test. Place the file in C:\Users\<user_name>\Documents\WICED-Studio-6.2.1\43xxx_Wi-Fi\libraries\test\wl_tool ( by default it should be the installation loc, update it for your installation if required). Modify the batch file based on the com port number. Hope it helps!

Refer to https://community.cypress.com/servlet/JiveServlet/previewBody/2360-102-3-16504/002-23156.pdf this document for detailed usage of WL commands

0 Likes
Anonymous
Not applicable

Thank you.After adding this batch into C:\Users\<user_name>\Documents\WICED-Studio-6.2.1\43xxx_Wi-Fi\libraries\test\wl_tool, is it required to dump the code again into kit?

Regards,

harshini

0 Likes
RaktimR_11
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

If you already have test.mfg_test application flashed in a CYW954907AEVAL1F EVK, there is no need to dump again as the mfg_test fw already have support for the WL commands used. Just running the batch file from command prompt should be sufficient.

Anonymous
Not applicable

Thank you

Regards,

harshini

0 Likes
Anonymous
Not applicable

Hi,

I am sending the pkteng_start 00:11:22:33:44:55 tx 100 1024 0 to test the WLAN kit in 802.11ac standard(5GHz band and 40MHzBW).While sending the packet,1024 bytes of data is going along with all payload data,header and preamble.How to find out pay load data alone in the whole 1024 bytes of data?Could u please help me hoe to finding out it.

Thanks&Regards,

harshini

0 Likes
RaktimR_11
Moderator
Moderator
Moderator
500 replies posted 250 replies posted 100 replies posted

You can use a sniffer like wireshark for that purpose to check the payload.

0 Likes