- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Everyone,
I'm new using tools from Cypress, so hope someone can help me to solve my doubt, i'm trying to program a CY8C322144 using the PSoC Programmer with Miniprog3, but at the moment when i try to select the family & device, i can't find it, someone knows if i need an additional library or how can i program this uC using the Miniprog3 Tool?
Best Regards
- Labels:
-
PSoC 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I cannot find anything about this part, and Cypress doesn't know it either: http://www.cypress.com/?app=search&searchType=part&keywords=CY8C322144&submit-keywords.x=0&submit-ke...
Is this one of the USB parts? Then you should ask in the appropriate forums, not in the PSoC ones...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
My mistake CY8C3244 Uc this is the device that i can't found using PSoC
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
CY8C3244 is a valid device and should be available on psoc programmer. What PSOC Programmer version are you running? Also make sure your Miniprog3 is properly connected and selected (check the port selection).
It i weird but when I open PSOC programmer without Miniprog3 or -50/-030 kit connected I can only see PSOC1 devices. It used to apear all devices in previous versions.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hmm. All devices shown by Cypress (http://www.cypress.com/?app=search&searchType=part&keywords=CY8C3244&submit-keywords.x=0&submit-keyw... ) are marked as 'in production', so they should be supported by the programmer. Did you update to the latest version (3.18.1) already?
Also, can you programm the PCoS3 directly from Creator, without starting the programmer manually? (Because this uses the Progammer internally)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello once again everyone
I´ll explain you shortly my problem, i need to program 2 cypress micros (CY8C21334 & CYC3244)
After some test, i'll resume some points:
1.-Install PSoC 3.13.1 version from cd (included in my miniprog3 kit)
i have the CY8C32XX family & my uC CY8C3244LTI-130 but i didn't have the 21x34 family & also the CY8C21334B-24PVXI
2.-Update the PSoC to 3.18.1 version & now the situation is:
I have the 21x34family & my uC CYC21334B-24PVXI but now i didn't have the CY8C32XX Family & CY8C3244LTI-130
Someone of you has been in the same situation?
thanks for your support!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- did you try to program the PSoC3 only from the programmer, or did you also try to use Creator directly (which shoiuld work since it doesn't need to run through the device selection)
- did you try auto-detect in the Programmer? maybe its just like zeta said - without MiniProg3 connected you don't see all devices for some reason (I had the same effect)
- When trying to select the device, is the MiniProg3 connected or not?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Everyone, I can not find CY8C4014 in device use psoc programmer 3.23 after reinstall, before I can find,who can help me?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Welcome in the forum.
Load your hex-file and attach to your programmer, the target will be selected automatically.
Bob