This content has been marked as final.
Show 8 replies
-
1. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
user_342122993 Aug 6, 2015 2:01 AM (in response to dgallatin95_1423736)You likely didn't install PioneerKit http://www.cypress.com/file/46011 -
3. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
user_14586677 Aug 6, 2015 5:49 AM (in response to dgallatin95_1423736)Something is pretty wacky, the attached is what you should see for templates.
Regards, Dana.,
-
PXSOC Creator Templates.JPG 100.7 K
-
-
4. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
dgallatin95_1423736 Aug 7, 2015 4:37 AM (in response to dgallatin95_1423736)HI Dana, that actually is what I see,but it's not what the tutorials show. They show Empty PSoC 3 Design template, Empty Psoc 4 Design template and Empty Psoc5 temlate I did finally get that when I uninstalled both the Creator 3.2 adn the kit software and installed CY8CKIT-042 Kit Setup (Kit Design Files, Creator, Programmer, Documentation, Examples) 592mb installed. Unfortuntely, this is Creator 3.0 which apparantly has a programming bugwhen I triedprogramming my kit, it wouldn't The error was PSOC saw the KitPRog device but only listed M0 cortex on the tree and said it wasnt supported Now I installed 3.2 again. andI have those same choices you show Which of those is for PSOC 4 pioneer ? The 4100/4200 one template? NOTE: when I go to Program, it now detects PSOC 4200M CY8C4247AZI-M485 under kitprog I should also note that my Pioneer kit appears to be different from the pics I have a round cap sense with arrows , not rectangular the RGB is below the Arduino headers to the right of the PMOD and I have a header for raspberry PI Should thier tutorial be updated? -
5. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
user_14586677 Aug 7, 2015 4:47 AM (in response to dgallatin95_1423736)Which of those is for PSOC 4 pioneer ? The 4100/4200 one template?
Yes, the 4100/4200 template.
Regards, Dana.
-
6. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
dgallatin95_1423736 Aug 9, 2015 8:17 AM (in response to dgallatin95_1423736)Hi thanks! Thats what it is, though in my case its the 4100/4200 M template There are 2 Pioneer kits(didn't realize that).Apparantly, I have the -44 one Have run into problem with Control Register API which I will post elsewhere -
7. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
bob.marlowe Aug 9, 2015 10:58 AM (in response to dgallatin95_1423736)So under the start page of Creator 3.2 ->Examples and Kits -> CY8CKIT-044 -> + you will find a lot of examples for your kit.
Most of them address the hardware on that pioneer board as CapSense and accellerometer.
Bob
-
8. Re: PSoc 4 Design template missing. Unable to create a PSoc4 design or select the device
user_14586677 Aug 9, 2015 12:46 PM (in response to dgallatin95_1423736)What is the problem with the control register ?
Regards, Dana.