Welcome to the Infineon Developer Community

I am using Application Kit TC3X7 V2.0 TFT board

I have configured BMHD but  the board all the time boots from Internal flash ignoring BMHD settings

If i want to use Alternate Boot Mode or BMI  to boot , which all changes i need to do on the board?

Hello,

We are trying to flash binaries which has empty cells using Infineon MemTool (version 4.08.01) after the P-Flash erased.
But the Memtool programing the empty cells with all zreo values.

SW is checking that area has in erased state or not. So, SW is not working b'coz empty cells have values all zeros. 

but other debugger flashing working with option: program empty cells "FALSE" setting

Please help us. if any setting required to do in Memtool 

Hi,

I want to translate the following App Note to Japanese. Please confirm to my work.
"Application note - MOTIX TLE987x Motor Control FOC Demo"
URL: https://www.infineon.com/dgdl/Infineon-MOTIX_TLE987x_Motor_Control_FOC_Demo_App_Note-ApplicationNotes-v01_00-EN.pdf?fileId=8ac78c8c8929aa4d0189441becff46d3

This application is large and will be divided into three parts.
I would like to translate pages 1 through 26 in this case.

Best Regards,
Hayashi.K

Hello Community, 

I am started using TC233  development board for few days and i ant now to display a hello wolrd or messga in the Console but i didn' found how to do i tried also to display it on the putty but also it doesn't work. 
is there any code exmaple or something that can help me. 

Thank you 

I inherited a project which uses a quite old version of the GCC toolchain when opening the project I receive the error:

Unable to find the tool chain with name: "ARM CM3-GCC 4.2.1". Select a different tool chain for your workspace.

How do I change the toolchain version of the project? I tried finding this version on the ARM developer project. The oldest version that I could find is 4.6 2012q4. Can someone point me to where to change the project settings or provide a link to the old version of the toolchain?

Dear All，

               I use the DAVE ide v4  with the nano library， calling the SPI-MASTER-EnableSlaveSelectSignal() and SPI-MASTER-DisableSlaveSelectSignal() functions cannot raise or lower the CS pin of SPI. However, when sending data through SPI, when using an oscilloscope to check the status of SCL and MOSI pins, they generate waveforms that are normal, but the CS pin remains in a high level state. 

              Configure this CS pin as an IO port, manually pull up or down the CS pin, but use the BUSY flag in the TBUF register as the completion of sending. When pulling up the CS pin, there will be a situation where there is still one byte that has not been sent, but the CS pin has been pulled up.

             What may be the reason why the two API functions generated by calling cannot control the CS pin state; How can I avoid manually raising or lowering the CS pin when there is still one byte of data not sent?

Thanks.

XMC4500-E144F1024 AC #

Hello, 

Please tell me how to use EVAL-1ED38x0DCT.
Even if you connect it to a PC via USB, the click start button will not appear and you will not be able to use it, as shown below.
Is there any solution?

best regards,

Hi,

I want to know CYT2B75CAE this controller is supporting AUTOSAR, If yes where i will get those information,

when i browse i am not able to find the information

Hello Colleagues,

I am looking into designing with the EZ-PD™ CCG7xC most probably the x=D version.

Using a Buck only configuration for the EZ-PD CCG7DC topology, with a variable DC power supply which may change its output voltage and current ( the voltage either higher but not higher than 21Volt or lower) to the EZ-PD CCG7DC at any time. My wish would be that when needed the EZ-PD CCG7DC should renegotiate the PPS values to the sink.

From the Application Note AN238890, it is stated that in page 13, that "The port will shut down if the input voltage drops lower than the output voltage because of the output voltage maintenance."

Can or will there be an automatic renegotiation of the output voltage, with the sink, to reflect the change in input voltage?

Can one write code to renegotiate a new PPS value with sink when this shut down happens?

Any ideas and documentation you have to help are much appreciated.

Thank you.

Jedison