All Forums
Browse the Community
USB
Universal Serial Bus (USB) forums have discussions regarding Low-Full & High Speed Peripherals, Superspeed Peripherals, USB Hosts Hubs Transceivers, and USB EZ-PD Type C product solutions for PCs and consumer device topics.
Wireless Connectivity
Power
Sensors
Memories
Memory Discussion Forums discussions regarding NOR Flash, SRAM, nvSRAM and F-RAM - performance and reliability with discrete memory densities ranging from 4K-bit to 2G-bit topics.
Other Technologies
Discussion forum regarding Other Technologies including Power Management and Clocks topics.
Security & Smart Card
Radio Frequency (RF)
Software
Software including ModusToolbox, PSoC Creator, WICED Studios and Wi-Fi Bluetooth for Linux .
Applications
Battery Management ICs
Infineon's TLE9012DQU is a multi channel battery monitoring and balancing IC for various lithium-ion battery applications, with integral functions like voltage and temperature measurement, cell balancing, and isolated communication with the main battery controller, including self-diagnosis features. The TLE9015DQU iso UART Transceiver IC is used in battery systems for enabling the communication between the main microcontroller and multiple TLE9012DQU units in a daisy-chain configuration. This forum welcomes discussions, queries, and insights on battery management systems and devices.
Featured Discussions
As mentioned in the title, I use Control Center on PC to recongnize CYUSB3014-BZXI device on PCBA and that's OK.
Here Control Center is in Cypress's suite for FX3 device.
However, when I power off my PCBA and PC, or just power off PCBA, Control Center occasionally shows no device after power on. On this circumstance, I could only unplug USB3.0 wire and plug it again, and it's OK again.
Add: PC's OS is win10.
It's not OK as follow:
Next it's OK after re-plug.
Show Less
Hi members,
I have a question about How can I erase SMU ALM7[7].
This Alarm is related to the SPU Module, However, in this IC, There is no SPU Module.
So I wonder why this alarm is activated and How can I erase this alarm.
Every time I turn on this IC, the alarm is set to 0x1.
And I tried to clear All the Alarm, but Alram 7[7] was always High.
please let me know that.
Thank you.
Show LessIm using tc377 for uart communication, I have to send data from tx without interrupt by using Timer(Gpt12)
when i using this Data is stored in Tx buffer but not transmitting to Rx.
This is timer function
void interruptGpt12_T3(void)
{
IfxCpu_disableInterrupts();
IfxPort_togglePin(LED);
if(g_flag1 == 1)
{
send_receive_ASCLIN_UART_message();
}
IfxGpt12_T3_setTimerValue(&MODULE_GPT120, RELOAD_VALUE_T3);
IfxCpu_enableInterrupts();
}
This one data transfer and receive function through uart
extern void send_receive_ASCLIN_UART_message(void)
{
IfxAsclin_Asc_write(&g_ascHandle, g_txData, &g_count, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &g_count, TIME_INFINITE); /* Receive data via RX */
}
Show Less
Hi, I can't add any printf or can't use UART from sample Ethernet application
if I add anything there it is crashing
I need to process data after receiving from Ethernet but if I try to do anything application just crash. So how and where to process Ethernet data.
Show LessHi, I am using Aurix TC375 Lite Kit development board and tried the freeRtos example code.
But after compilation, once the code is put in the debugger mode then the tsim issue comes as below snapshot --
Please get me a solution for this issue asap.
Thanks.
Show LessI am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall cysecuretools i got the message stating command already satisfied. This is all done on Windows.
Show LessSPI flash memory MT25QL128ABA1EW7-0SIT works well for FX3 SPI booting. When I used it for CX3 SPI booting, I am not able to let CX3 boot from SPI flash memory. PMODE pins configuration has been confirmed. Using control center utility tool, firmware image file can be written to MT25QL128ABA1EW7-0SIT successfully. But can't boot from it. it is still enumerated as boot loader device, which means it failed SPI booting. May I know the difference between CX3 and FX3 in terms of SPI booting? Thank you.
Show LessI am using Application Kit TC3X7 V2.0 TFT board
I have configured BMHD but the board all the time boots from Internal flash ignoring BMHD settings
If i want to use Alternate Boot Mode or BMI to boot , which all changes i need to do on the board?
Show LessHi,
I am using CY8C6245LQI-S3D42 and I used the DFU examples to boot the system and created the application to run on AM4 core and everything is working well.
I wait for 5 sec in DFU to check if there is any updates or just move with the Application code.
I find that sometimes the device stops booting once in a blue moon. Now If I flash again just the boot loader, everything is fine , I need not have to write the Application, it moves from DFU in 5 sec to application.
I believe, there is some how the flash/DFU is getting corrupted. I want to protect this scenario. Can some one share how do I protect my DFU so that it never erases . Any example's will be appreciable, I am using USB CDC transport in DFU.
Regards,
Madhav
Show Less-
TraveoII
UART buadrate Setting
by chandan1995 Jun 19, 2023