All Forums
Browse the Community
USB
Universal Serial Bus (USB) forums have discussions regarding Low-Full & High Speed Peripherals, Superspeed Peripherals, USB Hosts Hubs Transceivers, and USB EZ-PD Type C product solutions for PCs and consumer device topics.
Wireless Connectivity
Power
Sensors
Memories
Memory Discussion Forums discussions regarding NOR Flash, SRAM, nvSRAM and F-RAM - performance and reliability with discrete memory densities ranging from 4K-bit to 2G-bit topics.
Other Technologies
Discussion forum regarding Other Technologies including Power Management and Clocks topics.
Security & Smart Card
Radio Frequency (RF)
Software
Software including ModusToolbox, PSoC Creator, WICED Studios and Wi-Fi Bluetooth for Linux .
Applications
Battery Management ICs
Infineon's TLE9012DQU is a multi channel battery monitoring and balancing IC for various lithium-ion battery applications, with integral functions like voltage and temperature measurement, cell balancing, and isolated communication with the main battery controller, including self-diagnosis features. The TLE9015DQU iso UART Transceiver IC is used in battery systems for enabling the communication between the main microcontroller and multiple TLE9012DQU units in a daisy-chain configuration. This forum welcomes discussions, queries, and insights on battery management systems and devices.
Featured Discussions
Dear Team,
I am using the sequencer for analog input reading, just want to know what is difference between interrupt method and sequencer method for ADC1 reading?
Show Less Hello, I need your help. Thank you very much
It is normal for the program to jump from the boot area to the app area, but after jumping from the app area to the boot area, the program in the app area does not run normally, and it is looping in one place. The program keeps looping at 0x00C00090.
Now it is certain that the jump instruction is no problem, the program has jumped to the boot area, before jumping I have closed the interrupt. Or provide some code about software reset, I tried software reset, but it failed, maybe my instructions are not correct.
In the end, the target array is still all zeros
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/TRAVEO-T2G/cyt4fbb7-%E4%BD%BF%E7%94%A8mdma%E5%A4%8D%E5%88%B6%E6%95%B0%E7%BB%84%E6%B2%A1%E6%9C%89%E6%88%90%E5%8A%9F%E6%98%AF%E4%B8%BA%E4%BB%80%E4%B9%88/td-p/724114
Show LessHello,
Can you tell me how to update the firmware on the CYPD2119-24LQXI via USB?
Regards.
Dear Forum:
I know that
The Hex file generated by the Modus Tool box IDE follows the Intel Hex File format which is supported by the Cypress Programmer.
from the following title.
https://community.infineon.com/t5/PSoC-6/PSoC-programmer-parsing-failure/td-p/716946
I want to confirm that
Which IDE can generate hex file used by PSoC programmer?
Thank you.
Show LessHello,
I want to read the 1YN Bluetooth transmit power and write to it. How can I do this with the `hcitool`?
I'm using CYW4343A2_001.003.016.0031.0000.1YN.hcd firmware.
As far as I know CYW43439 has a maximum TX power of 8dB. If so is the following output wrong?
# hcitool -i hci0 cmd 0x08 0x004b
LE Read Transmit Power (0x08|0x004b) ncmd 1
Status: Success (0x00)
Min Tx power: -16 dBm
Max Tx power: 12 dBm
Thanks for all the help,
Mesih
Show LessHi All,
I have a question related to SCR_XRam and SCR_IRam.
The question: How to know whether the SCR_XRam and SCR_IRam are initialized or are not initialized in startup code?
Thanks.
Show LessFrom a linux system, I want to read back the configured program image from a CYC65215 part and check that its CRC is correct -- assuming it has an appended CRC. Does the image have a CRC? Is the CRC generated using a known algorithm with a standard polynomial? If so, which polynomial?
Show Less-
TraveoII
UART buadrate Setting
by chandan1995 Jun 19, 2023