- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I checked that WLTEST F/W downloaded to external Ext. flash is initialized in serial log.
but 'rwl_read_serial_port' failed error was printed in wl43362A2.exe as below.
$ wl43362A2.exe --serial 41 ver
5.90 RC230.255
rwl_read_serial_port failed: reached max retry limit.
query_info_fe: Reading CDC header failed
rwl_read_serial_port failed: reached max retry limit.
query_info_fe: Reading CDC header failed
Error -1 on query of driver dump
rwl_read_serial_port failed: reached max retry limit.
query_info_fe: Reading CDC header failed
C:\MinGW\msys\1.0\home\Ssery\wl_tool\wl43362A2.exe:
Error getting the last error
Why does this error occur?
Solved! Go to Solution.
- Labels:
-
Debug
-
SDK 3.x
-
Wi-Fi Direct
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
SDK-3.3.1 work as expected.
I have a 64-bit machine.
Please fresh install the SDK and try again. If needed SDK-3.1.2 could be used for mfg-test as well because the mfg-test only relays information between the serial terminal on the host and the Broadcom radios for wl commands.
Make sure the serial terminal used for displaying the debug messages is not connected. wl43362A2.exe uses the same serial port to send wl commands and receives responses.
BR.
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Does error message mean that wl43362A2.exe is available when 'WICED USB Serial Port' is connected only?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
'WICED UART Serial Port' driver is installed on the board, but the same error occurred.
Is there a setting conditions, such as MCU function required for wl_test?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Which version of the SDK are you using?
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
WICED-SDK-3.3.1 version is used.
The UART is set Speed = 115200, Databit = 8, Parity = No and Stopbit = 1,
wl command tools can't get the any data buffer from UART serial.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Which version WINDOWS ?
32 or 64 bits ?
I believed the wl43362A2.exe only could work on 32 bit or 64 bit only!
You better rebuild it wl43362A2.exe on your PC!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
SDK-3.3.1 work as expected.
I have a 64-bit machine.
Please fresh install the SDK and try again. If needed SDK-3.1.2 could be used for mfg-test as well because the mfg-test only relays information between the serial terminal on the host and the Broadcom radios for wl commands.
Make sure the serial terminal used for displaying the debug messages is not connected. wl43362A2.exe uses the same serial port to send wl commands and receives responses.
BR.
Seyhan