- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I was trying to implement client2ap application note posted by seyhan on evaluation board ISM43362_M3G_L44 but somehow i am getting error as shown below. While if same application note is compiled on BCM943362WCD4 it works perfectly. Can anybody tell me where am i making mistake.
Making .gdbinit
Building Bootloader
Finished Building Bootloader
Making DCT image
Compiling App_Client2Config_mode
Compiling Platform_ISM43362_M3G_L44
Compiling NetX_Duo
Compiling WICED
Compiling Lib_gpio_keypad
Compiling Lib_SPI_Flash_Library_ISM43362_M3G_L44
Compiling WWD_ThreadX_Interface
Compiling WICED_ThreadX_Interface
Compiling WWD_NetX_Duo_Interface
Compiling WICED_NetX_Duo_Interface
Compiling Supplicant_BESL
Compiling Lib_HTTP_Server
Compiling Lib_DNS_Redirect_Daemon
Compiling Lib_DNS
Compiling WWD_for_SDIO_ThreadX
Compiling Lib_Wiced_RO_FS
Compiling STM32F2xx
Compiling Lib_DHCP_Server
Compiling Lib_base64
Compiling common_GCC
Compiling STM32F2xx_Peripheral_Drivers
Compiling Lib_Ring_Buffer
Compiling STM32F2xx_Peripheral_Libraries
Making demo_client2ap-ISM43362_M3G_L44.elf
build/demo_client2ap-ISM43362_M3G_L44/libraries/App_Client2Config_mode.a(client2ap.o): In function `application_start':
F:\getlumos/apps/demo/client2ap/client2ap.c:126: undefined reference to `gpio_keypad_enable'
make.exe[1]: *** [build/demo_client2ap-ISM43362_M3G_L44/binary/demo_client2ap-ISM43362_M3G_L44.elf] Error 1
tools/makefiles/wiced_elf.mk:215: recipe for target 'build/demo_client2ap-ISM43362_M3G_L44/binary/demo_client2ap-ISM43362_M3G_L44.elf' failed
make: *** [main_app] Error 2
Makefile:185: recipe for target 'main_app' failed
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
It compiles and runs as expected with the following change,
if (event == KEY_EVENT_HELD) -> if (event == KEY_EVENT_PRESSED)
static void keypad_handler( gpio_key_code_t code, gpio_key_event_t event )
{
if (event == KEY_EVENT_PRESSED)
After the ISM43362_M3G_L44 is associated with your network then press reset button (SW3) to reset the board and ISM43362_M3G_L44 will connect to your network again. Then press the SW1 to switch to AP mode.
Also checktp make sure you use the correct patch fril from Inventek, http://www.inventeksys.com/inventekproducts/wifi-products/broadcom-wiced/
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Seyhan,
I tried the changes suggested by you but it is still giving the same error as posted earlier by me.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I have the same evaluation board, ISM43362_M3G_L44, and it works for me using WICED-SDK-3.1.2.
Perhaps you can reinstall the SDK and try again. Because "F:\getlumos/apps/demo/client2ap/client2ap.c:126" error is little confusing with "\" and "/" in the path.
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I tried reinstalling also,still it is not working. Even commenting out gpio_keypad_enable() results the same error.