- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I build, download and run the Sample P2P Application. But it only displayes following messages to the USB UART of the WICED evaluation board,
Platform BCM943362WCD4 initialised
Started ThreadX v5.5
Initialising NetX_Duo v5.6
Creating Packet pools
WWD SDIO interface initialised
There are two problems below
1. No other messages can be seen following the system messages above. I also run another sample scan application, got the same issue. It seems to me no print messages from application_start() can be displayed to the USB UART of the WICED evaluation board.
2. My android Tablet can't find "WICED-P2P" by opening WI-FI setting and enabling WI-FI Direct.
Can you help me out these issues?
Thanks
- Labels:
-
Wi-Fi Direct
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I believe you already install the USB Serial port driver for Wiced to communicate using USB. USB interface for Wiced evaluation board supports JTAG and serial ports.
For serial communication setup please take a look at Serial Port Communication to WICED Module.
Below code works as expected.
void application_start( )
{
wiced_init();
WPRINT_APP_INFO(( "\nP2P print application_start()...\n"));
besl_p2p_init ( &workspace, &device_details );
besl_p2p_start( &workspace );
}
The "P2P print application_start()..." text is printed on the serial terminal.
Thanks,
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
I still have the issue. I am using the Inventek Systems ISM43362-M3G-EVB Evaluation Board. I never see the ">" prompt. I can build, download and run the Sample P2P Application. But it only displays following messages to the USB UART of the Inventek system evaluation board,
Platform BCM943362WCD4 initialised
Started ThreadX v5.5
Initialising NetX_Duo v5.6
Creating Packet pools
WWD SDIO interface initialised
Any suggestion for fixing the issue. In addition, how can I order a Broadcom EVB like BCM943362WCD4?
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
I build a debug Sample P2P Application and the breakpoint hits following code. It seems to me that somewthing is wrong with Inventek EVB. ie correct? Did you see this on Broadcom EVB?
{
---> WPRINT_WWD_ERROR(("Could not initialize bus\r\n"));
return WICED_ERROR;
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Above code fails on BCM943362WCD4 as well, it is not a hardware issue.
The wiced_bus_init() is already called by the wiced_init(). Do you have wiced_init() in your application_start() then are you trying to reinitialize the bus?
Thanks,
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I do not have a setup with Inventek Systems ISM43362-M3G-EVB Evaluation Board. The Inventek System EVB is used by others as well, perhaps you are having problem with the make target. Are you using make target and referencing the ISM43362-M3G-EVB?
This make target is for BCM943362WCD4: snip.p2p-BCM943362WCD4-debug download run
Inventek System EVB target would be: snip.p2p-<InventekSystemEvbTarget>-debug download run
If you are interested in BCM943362WCD4 EVB please take a check out WICED Wi-Fi Partners website.
Thanks,
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyan,
I don't have the wiced_init() in my application_start(). I just build, download and run the Sample P2P Application in WICED SDK 2.4.1. It seems there is no issue with make target because I can use "snip.p2p-BCM943362WCD4-debug download" to build and download.
later I got a patch from Inventek at http://www.inventeksys.com/wp-content/uploads/Inventek_Systems_eS-WiFiPatch_2.4.0.zip
I installed it. But no difference. I have a question for you. Can you correctly run the sample p2p application on BCM943362WCD4 EVB? Can you see the device 'WICED-P2P' using a android tablet?
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
I use sample p2p code in p2p.c below
/******************************************************
* Function Definitions
******************************************************/
void application_start( )
{
wiced_init();
besl_p2p_init ( &workspace, &device_details );
besl_p2p_start( &workspace );
}
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please use "ISM43362_M3G_L44" as a platform.
Your make target should be like this "snip.p2p-ISM43362_M3G_L44-debug download run".
I do not have the same module as you have and I could not test it.
Testing with BCM943362WCD4, I do not have Android table to exercise P2P application.
Thanks,
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
When I use "ISM43362_M3G_L44" as a platform, I can't make target build and got errors below
**** Build of configuration Default for project Wiced-SDK ****
C:\Users\feng\WICED\WICED-SDK-2.4.1\Wiced-SDK\make.exe snip.p2p-ISM43362_M3G_L44-E-debug download
Making config file for first time
wiced_config.mk:150: *** Unknown component: ISM43362_M3G_L44. Stop.
make: *** No rule to make target 'build/snip_p2p-ISM43362_M3G_L44-E-debug/config.mk', needed by 'main_app'. Stop.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
After I installed the inventek patch for WICED SDK. Now I can run the sample p2p and see the the device 'WICED-P2P' using a android tablet.
Thanks