Studio Bluetooth Forum Discussions
I just updated to WICED 6.4 and copied the platform files from this thread: KBA223637
Is there newer platform files released for 6.4?
I get the following error:
\Documents\WICED-Studio-6.4\20719-B1_Bluetooth\WICED/common/spar_setup.c:162: undefined reference to `wiced_bt_set_app_start_function'
Show LessHello,
I was working on CYBT 213043 from almost a month. We were trying to include it on our product. lately the kit is not working. I am not able to scan or provision it. I did try resetting it and also i have not changed any code.
Any help is appreciated .
Thank you
Show LessHi,
I'm testing "HCI Commands for a RAM Download". When I go to WRITE_RAM command, it says
"xx xx xx xx is the 4-byte, absolute RAM address." I don't know what is absolute RAM address, where can I get this parameter? I used CYBT-343026-01 EVAL board to do the testing.
BR,
Treacy
Show LessIn WICED 6.2.1 I could see wiced_hal_i2c_select_pads(scl_i2c, sda_i2c) only in the API for 20735_B1, but not for 20719_B1?
So what is the solution for 20719?
Thanks
Show LessHi again,
we have another question.
Is it documented anywhere which functions are not implemented, even though they are found in the header files and the API reference guide? This would save us a lot of the time that we've spent chasing our tails.
regards,
Ed Pearson
Show LessHi,
I want to download FW to cybt-343026-01 module. But always have below fail. I have tried with EVAL(EVAL has two port shown in PC and I select the HCI port), it is OK.
Module connect usb to PC only one port, so I just modify the COM port number.
********* Download Failure *************
+-----------------------------------------------------------------------------------------------+
| Follow below suggestions and retry.
|
| 1. Verify USB-UART driver is correctly installed
|
| 2. Verify SW4 switches are in ON position (CTS, RTS, RXD, TXD)
|
| 3. Power cycle CYBT-343026-EVAL and retry. |
|
|
| If this problem persists, the serial flash on the board may be corrupted. |
| Follow below steps to reset CYBT-343026-EVAL board to factory default state. |
| Note: This will erase any user applicaiton in the memory and reset the board to dafulat state |
| 1. Press and hold RECOVER button (SW2)
|
| 2. Press and hold RESET button (SW1) for 1 second
|
| 3. Release SW1
|
| 4. Release SW2
|
| 5. Re-program the board
|
+-----------------------------------------------------------------------------------------------+
I have done as above saying "Press and hold RECOVER button;Press and hold RESET button (SW1) for 1 second.......", but same fail.
I also do as Programming an EZ-BT WICED Module – KBA223428 saying "Pull SPI2_MOSI to GND then reset", but same fail
1. Press RECOVER button mean set RECOVER pin to high,right?
2. What can I do next?
Show LessWhat functionality can use to provide delays for porting u8g2 libray (SSD1306-I2C) to CYW20719?
Or what is the alternative of PSoC's CyDelay*() API functions available for CYW 20719?
Thanks
Show LessHi,
I'm using client control tool to test dowanlod FW function. But it always fail. I think device have enter the downalod mode and use WICED-Studio tool is OK for downaloding. Why?
Show Less
Hello,
I am currently measuring Tx Power of CYBT-353027-02 with LitePoint IQxel80 instrument.
However, I can merely measure Tx power aroud 8.7 dBm even though I set the power as maximum Tx power table 0x00 in cyBluetool as shown below.
Is there any issue on the BT module?
Could you look into this problem and suggest any of tryinig to do?
Below is the result of measured Tx power with power table 0x00.
Compared with measured Tx power and the power in data sheet, I can not increase Tx power up to 12dBm even though I set Tx power table as much as high (0x00).
(Data sheet Link : page 26, https://www.cypress.com/file/416356/download )
I used cyBluetool to control DUT and test configurations are like below.
The demo hello sensor application is installed on the BT module using WICED studio 6.2.
Thank you for your time and your support in advance.
Best regards,
Eunsung
Show Less