Hi All.
Our customer going to make Audio device through CYBT-343026-01.
Can i embody A2DP in the Non-OS through CYBT-343026-01?
And Can distribute with Firmware form possible?
Please check this question.
Thank you.
Show LessHi
I am use CYW20706A2. and I want to connect special central device(BLE)
special central device prefer use LE 2M.
so it send LL_PHY_REQ after device connected. But CYW20706A2 don't send LL_PHY_RSP
(my SDK is wiced studio6.4 and modus2.2(BTSDK2.8))
According to "BT Core Doccument", if device receive LL_PDU_REQ, device have to send LL_PDU_RSP
But CYW20706A2 don't send it and LE data packet for connection.
so device is disconnected. why don't send LL_PHY_RSP on CYW20706A2??
We would like to know that cypress supports any universal programmer like Cyclone FX, Cyclone LC and SMH flash runner.
So can you please suggest a universal programmer that should support to program the BLE module (CYBT-343026) and controller (CYT2BL).
Show LessWe want to control the output of the GPIO by changing the registers.
Is it possible to know the address of the register?
This is because we are using a dynamic test tool.
Thanking in advance.
Otsuki
Show LessHello,
What is the API to get the packet statistics (Tx and Rx) on a SCO session?
I am using WICED SDK 6.4 on 20706 based module. I have implemented an HFP Audio Gateway. This was based on the demo hci_audio_gateway. The PCM is routed to I2S.
During the testing we are encountering the audio loss after a long run in one direction. Audio codec is negotiated as mSBC. Looking for packet stats to assist with debugging.
Thankyou
Praveen
Hello sir,
请问下CYBLE-013025-00 透传的协议文档在哪里可以找到?
谢谢
Hello
1.
I was previously taught by the thread below how to use CYBT-343026-01 in HCI mode.
https://community.cypress.com/t5/WICED-Studio-Bluetooth/About-the-WICED-HCI-protocol/m-p/57884#M1051
When I used the Inquiry command to search for peripheral devices after booting in HCI mode, no Inquiry result was returned.
Do I need to make any other settings after booting?
(I can find multiple devices by running the Inquiry command in EZ-Serial mode.)
2.
I also found the description However you may need to program it initially with firmware / patches. In the thread below.
Also, does this have anything to do with the behavior in Question 1?
Isn't it possible to use standard HCI just by switching to HCI mode by operating SPI_MOSI and CTS at reset?
Is it possible to provide firmware / patches for Android?
Best Regards
Hayato
Show LessHello,
I installed WICED-Studio-6.6 for mac (Big Sur, 11.1) to run my CYW920706WCDEVAL Evaluation Kit.
Despite of successful installation, I can not see the 20706-A2_Bluetooth folder in WICED-Studio-6.6 under Documents. But I can see 43xxx_Wi-Fi folder instead.
tried also reinstallation but there is still no 20706-A2_Bluetooth folder.
am i doing something incorrectly? or is there anything to do more during installation?
Regards,
Eunsung
Show LessHello,
I started exploring the CYBT343026-01 module, to understand if it usable as a serial interface between an external device communicating through UART and a PC or a Smartphone. I was able to successfully connect and communicate data using the module, but I am not able to enter the command mode through the COM port associated to the SerialPort profile of the Bluetooth module. I can access the command mode just through a connection to the PUART pins. Unfortunately this procedure is not possible in my final application, as the module will not be connectable to an external host for sending commands through the UART, but I still need to access the command mode to configure and update it. Is there any way to enter the command mode using the classic Bluetooth or the BLE communication interface?
Thank you
Show LessWhen I run sdptool search SP, the device(android smartphone) displayed available SP service and channel as 8. This device has bluetooth terminal app.
sdptool search SP
Inquiring ...
Searching for SP on mac_adddr ...
Service Name: Serial Port
Service Description: COM Port
....
Service RecHandle: 0x10000
Service Class ID List:
"Serial Port" (0x1101)
Protocol Descriptor List:
"L2CAP" (0x0100)
"RFCOMM" (0x0003)
Channel: 8
...
"Serial Port" (0x1101)
Version: 0x0100
But I was not able to get SP service of another android device(doesnot have bluetooth terminal app) by running same (sdptool search SP).
sdptool search SP
Inquiring ...
Searching for SP on mac_adddr ...
and it terminates.
When I tried sdptool browse mac_adddr ,the output resulted with no SP support.
When I run same commands to get service of ios device, I was able to fetch Serial Port (SP) and it's channel of iOS device.
Whether android device doesnot expose it's serial port and channel number? How can I get the channel number without bluetooth terminal application?Whether bluetooth terminal app creates SP channel for android device and it doesnot have it's own?
Thanking in advance.
Show LessEmployee
Employee
Employee
Contributor
Employee
Employee
Employee
Contributor