- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
As a follow on to this thread: No access to CYBT-343026-EVAL board's Make Targets
I'm trying to test the CYBT-343026-EVAL card with Wiced, so I followed all the previous steps.
When I build Make Target "demo.hello_sensor-CYBT_343026_EVAL download" Wiced can not detect my device ...
Detection device ...
********* Detection fault *************
+ ------------------------------------------------- ----------------------------------------- +
| The CYBT-343026-EVAL card was not detected. Verify that the device is connected |
| power cycle if necessary to restart in programming mode, and try again. |
| |
| Refer to the Appendix sections of the Quick Start Guide to learn about common COM port problems.
+ ------------------------------------------------- ----------------------------------------- +
So I tried to put my device in recovery mode (with SW2 switch switch), without success too.
Do you have any idea why this is not working?
Regarding,
Thomas
Solved! Go to Solution.
- Labels:
-
ispn:40226:1:0
-
l1:314:1:0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Please have a look at below blog and try out the methods mentioned: (section 3 - Programming with Recovery Procedure )
https://community.cypress.com/docs/DOC-14990
https://community.cypress.com/message/161356#161356
Thanks & Regards,
Anjana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Please have a look at below blog and try out the methods mentioned: (section 3 - Programming with Recovery Procedure )
https://community.cypress.com/docs/DOC-14990
https://community.cypress.com/message/161356#161356
Thanks & Regards,
Anjana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks a lot for your help Anjana but it's still not working .. I tried pretty much everything.
Have this now :
Downloading application...
********* Download Failure *************
+-----------------------------------------------------------------------------------------------+
| Follow below suggestions and retry. |
| 1. Verify USB-UART driver is correctly installed |
| 2. Verify SW4 switches are in ON position (CTS, RTS, RXD, TXD) |
| 3. Power cycle CYBT-343026-EVAL and retry. |
| |
| If this problem persists, the serial flash on the board may be corrupted. |
| Follow below steps to reset CYBT-343026-EVAL board to factory default state. |
| Note: This will erase any user applicaiton in the memory and reset the board to dafulat state |
| 1. Press and hold RECOVER button (SW2) |
| 2. Press and hold RESET button (SW1) for 1 second |
| 3. Release SW1 |
| 4. Release SW2 |
| 5. Re-program the board |
+-----------------------------------------------------------------------------------------------+
Download failed. This WICED platform of the SDK only supports download to 20706A2 device.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
- Can you please confirm you have copied the Platform files in the correct folder as in the fig below
- please make sure you have selected HCI UART only for programming. Try with adding HCI UART com port in the make target and download (demo.hello_sensor-CYBT_343026_EVAL download UART=COMxx). (make sure the device is in recovery mode before downloading)
- Also , please have a look at following thread who had similar issue - How to download program into the module CYBT-343026-01 in WINCED 6.2
Thanks & Regards,
Anjana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
-I am sure I copied the correct platform file
-I already added the right COM in the "Build Make Target" target
Maybe this is only the problem comes from my Eval Board ... It's possible (I'm going to order a new one, to check)
Regards,
Thomas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Not sure, But yes please try with another board as well as on another PC.
Thanks,
Anjana