- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I was trying to execute the HCI Commands, when i sends commands i'm getting the error as shown below
once i give manual reset its working fine, that is also only one time, after that no response back as show below
And when i'm trying to execute the LE Receiver Test, getting the below response
kindly help to identify the mistake i was doing.
Thanks
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
1. Please unzip the file I give you before. You can build a new file (named as "customer" for example) under the apps file. Then move the hello_sensor file that I gave you into it.
2. Then right click on the wiced SDK "apps" column and select refresh. Then you will see the hello_sensor file in it.
3. In the "make target" column, create a new make target named "customer.hello_sensor-CYW920719Q40EVB_01 download".
4. Plug the Q40 Kit board to your computer and double click the "customer.hello_sensor-CYW920719Q40EVB_01 download" . You should see the board was successfully programmed.
5. Unplug the Kit board and plug it on your computer again. Open the command window and use the mbt command to set the right COM port as you did before. Then you can use the mbt command successfully.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Could you please try with mbt tool and confirm if you are getting the response correctly?
Thanks,
Anjana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks for the reply.
i tried with mbt tool as wel, their also i was not getting correct response.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Like below i'm getting the error. when i'm using mbt tool
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please download an empty project which only has the wiced_transport_cfg_t init program and then try the mbt tool again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Can u share the config file to download.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Yes, i had done the mbt reset before doing LE tx test. can you share the file to download. and for reset also first time i wanted do manual then only it is reset by command. kindly check below
Thansk
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
i'm getting the below response
Can u suggest how to resolve this issue
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please use the demo code in the last reply.
After you program the device, set the right port with "set MBT_TRANSPORT=COMxx".
Then unplug the device from your computer and plug it again.
Try the "mbt reset" command, you should be able to use the other test command.
I attach the screenshot for your reference.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I had loaded the demo code which you had shared, but after that also i'm not getting the event response. One thing is that when i give manual reset and then try with mbt reset command its working fine, after that if i try for other commands i'm not getting any response/ event.
Kindly help me to find out the issue.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Did you try to unplug the kit board from your computer and plug it again?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
yes, i did that as you mentioned in the last discussion.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Is the device will be in advertise mode, when i dump the code that you had provided. Because i'm seeing in Cypress Bluetooth application in the name of hello & -30dBm power level. so let me know whether i'm missing anything.
And i'm following the below procedure to dump hello sensor into the device, please confirm that i'm following the correct procedure or not, if not can you explain how to do it.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
1. Please unzip the file I give you before. You can build a new file (named as "customer" for example) under the apps file. Then move the hello_sensor file that I gave you into it.
2. Then right click on the wiced SDK "apps" column and select refresh. Then you will see the hello_sensor file in it.
3. In the "make target" column, create a new make target named "customer.hello_sensor-CYW920719Q40EVB_01 download".
4. Plug the Q40 Kit board to your computer and double click the "customer.hello_sensor-CYW920719Q40EVB_01 download" . You should see the board was successfully programmed.
5. Unplug the Kit board and plug it on your computer again. Open the command window and use the mbt command to set the right COM port as you did before. Then you can use the mbt command successfully.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks!
Now it is working