Anonymous
Not applicable
Nov 12, 2013
07:45 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 12, 2013
07:45 PM
Hi Team, I found a issue by disabling "powersave_timeout" mode. Is any setting config which i miss ? thanks a lot.
Disable "powersave_timeout" modeThere are one strange issue about
Solved! Go to Solution.
- Tags:
- 0x00
- 3min
- 40sec
- alert
- blink
- button
- char
- consumption
- crash
- default
- default_adv
- disable
- duration
- enable
- endif
- find
- fix_cq_1362942
- found
- high_undirect_adv_duration
- high_undirect_adv_interval
- if
- ifdef
- interval
- issue
- low_undirect_adv_interval
- low_undirected_adv_duration
- low_undirected_adv_duration=
- mode
- module
- number
- pathloss_check_interval
- power
- powersave_timeout
- result
- second
- seconds
- slots
- status
- status_led_enable
- test
- timeout
- uint16
- uint8
- uuid
- uuid_characteristic_alert_level
- uuid_characteristic_battery_level
1 Solution
Nov 22, 2013
11:18 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 22, 2013
11:18 AM
You cannot use the create function of one application with the configuration of another. For all practical purposes, proximity_plus is a different application compared to proximity - it enhances proximity application by registering its own callbacks to handle events. In other words, proximity_plus (bleprox_mod_Create) has already modified proximity app (bleprox_Create).
7 Replies
Anonymous
Not applicable
Nov 13, 2013
07:28 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 13, 2013
07:28 PM
Is anyone duplicated this issue as well ? @@" I test the proximity sample code and only modified the db config.thanks.
Nov 14, 2013
08:40 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 14, 2013
08:40 AM
I will investigate today with the software team Frank.
Anonymous
Not applicable
Nov 17, 2013
11:41 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 17, 2013
11:41 PM
Hi Teams, Because I must reply customer that is it a unknown or known issue, >"< Can you please check if BRCM can duplicate this issue or not? If not, I think it is our issue and need to analyze root cause further. Thanks.
Nov 18, 2013
04:36 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 18, 2013
04:36 PM
Frank,The firmware team has a few items in their queue that they will need to complete before they can move onto testing the code you provided (perhaps in the next few days). However, they confirmed that this is not a known issue with the BCM20732S, which has been on the market for some time now.
Anonymous
Not applicable
Nov 19, 2013
02:29 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 19, 2013
02:29 AM
Hi Teams, I do a test and found a abnormal situation. 1. run the "proximity_plus" sample code ==> Pass 2. run the "proximity_plus" sample code with following modified ==> Failed APPLICATION_INIT() { bleapp_set_cfg((UINT8 *)bleprox_mod_db_data, bleprox_mod_db_size, (void *)&bleprox_mod_cfg, (void *)&bleprox_mod_puart_cfg, (void *)&bleprox_mod_gpio_cfg, bleprox_Create); } @_@a
Anonymous
Not applicable
Nov 22, 2013
04:33 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 22, 2013
04:33 AM
Hi all, Can someone please advise about how to modify "bleprox_Create" function and to avoid "crash" ? thanks a lot.
Hi Teams, I do a test and found a abnormal situation. 1. run the "proximity_plus" sample code ==> Pass 2. run the "proximity_plus" sample code with following modified ==> Failed APPLICATION_INIT() { bleapp_set_cfg((UINT8 *)bleprox_mod_db_data, bleprox_mod_db_size, (void *)&bleprox_mod_cfg, (void *)&bleprox_mod_puart_cfg, (void *)&bleprox_mod_gpio_cfg, bleprox_Create); } @_@a
Nov 22, 2013
11:18 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 22, 2013
11:18 AM
You cannot use the create function of one application with the configuration of another. For all practical purposes, proximity_plus is a different application compared to proximity - it enhances proximity application by registering its own callbacks to handle events. In other words, proximity_plus (bleprox_mod_Create) has already modified proximity app (bleprox_Create).