USB superspeed peripherals Forum Discussions

Hi 

I would like to request for the following information for CYUSB3014-BZXI that I am unable to locate from the datasheet:

1. Maximum Junction Temperature (Tj_max)
2. Junction-to-Board thermal resistance (Theta_JB)
3. Junction-to-Case (Top) thermal resistance (Theta_JC (Top))

Thank you!

Hi all,

I have a  task of operating BIST on Cypress(CYUSB3014-BZXC) embedded controller. Commands are operated from PC via USB. 

Please help me to do it step by step, from the point of view of hardware (if any steps are necessary) and software.

The test is online, means that after completing BIST Cypress has to return to  regular operations without system rebooting or communication channels reestablishing.

I have seen in the Cypress documentation that there is a limited BIST supported - only for high speed communication channels. I did not see that any BIST is mentioned for other peripherals, memory, etc..   May be I simply did not see the the relevant information.   I have to have maximum functionality available. 

Anyway I do not understand how to operate BIST,  then get the results and return to operational mode.

Please advise.

Thank you in advance,

Roman 

Hello,

I see that there is no Mac M1 driver for the EZ-USB GX3 / CYUSB3610.

When can we expect a driver for macOS 12+ Monterey for the M1 (arm64) architecture?

I see that the Linux driver is Open Source. Perhaps the Xcode project and source for macOS 11 could be released so that interested parties could port it to macOS 12 more easily?

Cheers,
Joe

Reference: 
https://community.infineon.com/t5/USB-superspeed-peripherals/EZ-USB-GX3-CYUSB3610-M1-Mac-Drivers/m-p/281767

Hi there, 

Just a simple question..

Can I left open "U3RXVDDQ" and "U3TXVDDQ" when using  CYUSB3035-BZXI but only with USB2.0 connector?

We have a chance to revision the PCB and design so I am curious whether or not I can remove the power from "U3RXVDDQ" and "U3TXVDDQ"?

@JayakrishnaT_76 , can you kindly help me on this?

Thanks!

Can someone help me find project files for AN84868 anywhere. Only the PDF file is available here:

https://www.infineon.com/dgdl/Infineon-AN84868_Configuring_an_FPGA_over_USB_Using_Infineon_EZ-USB_FX3-ApplicationNotes-v06_00-EN.pdf?fileId=8ac78c8c7cdc391c017d073ae99e5f24

Thanks

Hi , on my device there no UART pins. 

I take the reference of "cyfxusbdebug" example code to print the Debug messages on USB interface. 

I configure the Endpoint as interrupt endpoint. 

epCfg.enable = CyTrue;
epCfg.epType = CY_U3P_USB_EP_INTR;
epCfg.burstLen = (usbSpeed == CY_U3P_SUPER_SPEED) ? (BURST_LEN) : 1;
epCfg.streams = 0;
epCfg.pcktSize = size;

/* Interrupt  endpoint configuration */
 CyU3PSetEpConfig(CY_FX_EP_DEBUG, &epCfg);

After that I make the entry this endpoint on "cyfxusbdscr.c"   in   CyFxUSBSSConfigDscr[], CyFxUSBHSConfigDscr[],CyFxUSBFSConfigDscr[]  descriptors 

And Host application retrieve the data through interrupt endpoint.

while (1)
{
// cout << "In Thread" << endl;
if ((lpParams->IsOpen() == TRUE) && 1)
{
if (lpParams->InterruptInEndPt)
{
length = lsize - 1;
if ((lpParams->InterruptInEndPt->XferData(fInBuf, length) == FALSE))
{
Sleep(100);
cout << "InterruptInEndPt->XferData Failure!" << endl;
}
else
{
cout << "RD= " << length << endl;
if (length == 0)
{
cout << "IN THREAD LENGTH_0" << endl;
#if 0
if ((m_bLogFileOpenFlag == TRUE))
{
fclose(wrLogFile);
m_bLogFileOpenFlag = FALSE;
}
#endif
Sleep(100);
}
else
{
cout << "IN THREAD LENGTH_NON_0" << endl;
fInBuf[length + 1] = '\0';
#if 0
if (m_bLogFileOpenFlag == FALSE)
{
wrLogFile = fopen(DEBUF_FILE_NAME, "a+"); //TODO FIle check
m_bLogFileOpenFlag = TRUE;
}
#endif
// Sleep(100);
wrLogFile = fopen("./Fwlog.txt", "a+");
fwrite((fInBuf /*+ 8*/), 1, length, wrLogFile);
fclose(wrLogFile);
}
}
}
else
{
cout << "No Interrupt Endpoint on Device" << endl;
break;
}
}

this error 

InterruptInEndPt->XferData Failure! 

 The Debug are not coming ??

Hi,

We got a new proposal design where we connect two FX3 to the CYUSB4347-BZXCES as below. Currently the design are still in proposal and we do not have CYUSB4347-BZXCES.

Currently our one FX3 solution design is working PC<->FX3<->FPGA. We also understand that if connect two FX3 to PC directly via two USB cable also should work just by checking the devicecount in c++ API. I got vey little info on CYUSB4347-BZXCES device on firmware design or API, it only has share a .bin file.
https://www.infineon.com/cms/en/product/universal-serial-bus-usb-power-delivery-controller/hub-controllers/hx3pd-usb-3.1-gen-2-pd-hub/cyusb4347-bzxces/#!tools

Question:

1.)  is CYUSB4347-BZXCES plug and play solution? where i expect our current software/firmware do not need to change by connecting as above design. the worst case is just flash the Cypress provided bin file thru USB and we expect it to be working.
2.) Can current FX3 API still recognize the FX3_A and FX3_B with "devicecount" with above configuration? or any software need to change for above configuration?

Thanks

Hi, I have a C++ program that sends data from my Linux host PC to the FX3, and then has the FX3 return that data back to the host. I would like to read some registers and log them in a file on my host PC during all of these data transfers. I've found the CyU3PReadDeviceRegisters() API function, but I don't know if it needs to be in the C++ program I wrote, or the firmware I have downloaded onto the FX3 using the USB bootloader. I am using the cyfxbulklpautoenum image file that comes with the Linux cyfx3sdk.

To summarize, can I get an example program or code snippet describing where to use the CyU3PReadDeviceRegisters() function (either in firmware or C++ program) and how to log that data for each transfer onto my Linux host computer?

Thank you.