- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
AN61345 app note is for interfacing fpga to fx2lp...
if i interface image sensor to fx2lp...what modification i need to do??
or any other app note cypress provide for interfacing image sensor to fx2lp through gpif??
if any...let me know
thank you
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Slave FIFO cannot be used to interface image sensor. The image sensor uses different type of control signals as compared to SlaveFIFO.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Slave FIFO cannot be used to interface image sensor. The image sensor uses different type of control signals as compared to SlaveFIFO.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Any other reference to interface image sensor to fx2lp?
let me know?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
There is no reference design for a UVC class example with image sensor and FX2LP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
But i need it for my project,any other solution or method?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
UVC class application is not feasible with FX2LP if the UVC headers are to be added inside FX2LP as the core frequency is only 48 MHz. You will get at max around 2-3 frames per second using UVC class.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
my sensor is contineously streaming,i dont need i2c interface also and i
dont need uvc headers also
what can i do now?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Then you can design the state machine that accepts the image sensor data based on FV and LV and send it to USB.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
reference for that?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
No reference for that.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
thank you...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Then you can design the state machine that accepts the image sensor data
based on FV and LV and send it to USB
-->OK
If i create own stae machine and gpif interface for image sensor...i will
get .c file
can i use this .c file in slavefifo firmware?by doing required
modification??
if its not possible...which firware should i use??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
mddd
Then you can design the state machine that accepts the image sensor data
based on FV and LV and send it to USB
-->OK
If i create own stae machine and gpif interface for image sensor...i will
get .c file
can i use this .c file in slavefifo firmware?by doing required
modification??
if its not possible...which firware should i use??
any answers?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
You need to handle the UVC level protocol in the firmware too..