CYUSB3065の画像出力について

Tip / ログイン to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
lock attach
Attachments are accessible only for community members.
TeMa_2997106
Level 6
Level 6
Distributor - TED (Japan)
10 likes received 10 solutions authored 250 replies posted

現在以下の解像度をISPから出力しています。(CX3への入力)

1920x1080@30fps

この解像度をCX3へ入力した場合、CX3が出力するデータをキャプチャソフト(NVCap)上で表示すると

フレームレートが半分の15fpsと表示されます。映像はシームレスに表示されるとのことで、15fps以上は出ているようです。

CX3のPCLK,SYNC出力端子には信号がでており、VSYNCは30fpsを示しています。

このようなケースではCX3で何が発生しているかわかりませんでしょうか?

下記を見ると、CX3は最低V-Blanking時間があると参考記事を見かけました。これも上記現象の要因となりますでしょうか?

CX3から出力するVSYNCを見るとV-Blankが88.75usでした。

https://community.cypress.com/thread/36130

ディスプリプタは添付のとおりです。

正しく設定しているつもりです。

宜しくお願いします。

0 件の賞賛
1 解決策
TeMa_2997106
Level 6
Level 6
Distributor - TED (Japan)
10 likes received 10 solutions authored 250 replies posted

本件、ISP側の設定(V-Blanking中のSOFパケットの位置を)を変更することにより、正常に画像が出るようになりました。

本デバイスと関係ない箇所の問題でありました。お騒がせしました。

元の投稿で解決策を見る

0 件の賞賛
5 返答(返信)
JayakrishnaT_76
Moderator
Moderator
Moderator
First question asked 1000 replies posted 750 replies posted

Hello,

From the description, I understand that the sensor is configured to output data at 30fps but you are able to see only 15fps on the host side. Please confirm if my understanding is correct. If this is the case, then it can be due a shorter V blanking time.

As mentioned in the thread (link below), if you are using SDK 1.3.4, then please set a minimum V Blanking of 200uS. If you are using SDK 1.3.3, then please set a minimum V blanking of 500uS.

the output frame rate of cx3

Please try this and let us know if you still see reduction in frame rate.

Best Regards,

Jayakrishna

Best Regards,
Jayakrishna

念のため、Post #1のポイントのみ再度記載させて頂きます。

今回の問題はV blanking時間が短いことが考えられます。

ご質問の中で記載されているthe output frame rate of cx3のように、もしSDK1.3.4をご使用の場合、V blanking時間の最小値200uSをセットしてください。SDK1.3.3の場合はV blanking時間の最小値500uSをセット。

もしこの設定で問題が発生する場合、ご連絡ください。

以上、よろしくお願い致します。

0 件の賞賛
TeMa_2997106
Level 6
Level 6
Distributor - TED (Japan)
10 likes received 10 solutions authored 250 replies posted

ご回答ありがとうございます。

わからない点があるので教えてください。

「V Blankingの最小値」というのは、どこでセットするのでしょうか。

Receiver ConfigurationでV-BlankingのLine数は指定できますが、時間について指定するところはありません。

設定する場所があるのでしょうか。

よろしくお願いします。

0 件の賞賛
TeMa_2997106
Level 6
Level 6
Distributor - TED (Japan)
10 likes received 10 solutions authored 250 replies posted

本件、ISP側の設定(V-Blanking中のSOFパケットの位置を)を変更することにより、正常に画像が出るようになりました。

本デバイスと関係ない箇所の問題でありました。お騒がせしました。

0 件の賞賛

ご連絡、ありがとうございます。

また何かございましたら、ご連絡ください。

よろしくお願い致します。

0 件の賞賛