USB low-full-high speed peripherals Forum Discussions

Hi. 

Our company want do a Driver Re-sell process.

While reading and following CyUSB.pdf, I have a few questions below.

1. How can I create case for Driver Re-sell?

-   I entered www.cypress.com/support but still I do not know how to do it. 

-  At the previous questions about Driver re-sell, there was a answer that recommend to contact Cypress Local sales/FAE.

 But they also do not know how to do it.

if anybody knows the contact point or mail address about this, please let me know.

2. For the INF file, Should I change the GUID to new one so that have a different GUID with cypress's one?

we just want to change VID/PID for our product without changing any other functionality of the driver.

3. For the prerequisites, the document said we need to prepare below;

  1) EV certificate Code signing Certificate

  2) Microsoft Dashboard Account

  3) HLK studio.

       we have 1), 3) now but I don't know how to get Microsoft Dashboard Account.

        is it the same one with the Microsoft Account which we are using for Microsoft Office 365? or do we need to follow https://partner.microsoft.com/en-US/dashboard/registration/hardware to get Partner Center account?

hello,

I want to attach an ox03a10 camera to my pcb, can someone tell me how I could configure it to be able to take the picture ? thank you

Dear Sir/Madam,

GreenSoft Technology, a leading provider of environmental compliance data management services and software for the global electronics industry (http://www.greensofttech.com), has been contracted by Teledyne DALSA to collect compliance data on parts purchased from your company. Please refer to attachments for a letter of authorization from Teledyne DALSA and a list of part numbers. Please note that Teledyne DALSA might not purchase directly from your company but via a supplier or distributor. In addition, you might need to collect material or compliance documents from your suppliers such as raw material manufacturers to fulfill your customer’s requests. Your support to your end customer is appreciated.

Can you please provide the following environmental compliance data for these parts:

• REACH Declaration or SVHC Certificate. If a product contains any SVHC or Substances of REACH - Annex XIV, please provide the substance name and concentration, as well as future plan to eliminate its use.
• If reportable SVHCs are identified, Substances of Concern In articles as such or in complex objects (Products) (SCIP – per Waste Framework Directive 2008/98/EC, amended by Directive (EU) 2018/851).
• Full Material Disclosure (FMD), MSDS or similar document in your standard format if available

If you cannot recognize a part or it's incorrect, please indicate such in your feedback.

Please respond as soon as possible or provide an expected date of completion and we will follow up. We may contact you if any clarification is needed. Teledyne DALSA is committed to providing its customers with products that meet the highest standards of innovation, performance and environmental safety and expects your timely response

If you have any questions, you can contact me at Cora@greensoft-china.com or call +1 323-254-5961 x813 (I am based in China; we also have someone in our US office that can answer your questions).

Best Regards,

Cora Zhang

Project Engineer

Cora@greensoft-china.com

GreenSoft Technology – China Office

No 368, North Xinshi Rd, FL12

Shijiazhuang,Hebei, China

(China Office) Ph: +86-311-8386-4638

GreenSoft Technology

155 S. El Molino Ave, Suite 100,

Pasadena, CA 91101, USA

(US Office) Ph: 323.254.5961

www.greensofttech.com

GreenSoft Technology, Inc

My system have a EZ-USB FX2LP.

In "Receiver sensitivity Test", my system is failed.

"Pass Limits:<= 200.000 mVDevice receiver sensitivity [218] (Worst of 2 Trials)229.100 mV # Trials Run: 2Worst Trial: Trial 1"

Is there a control register for "Receiver sensitivity"

Thanks.

I have a custom board based on the FX3S processor with an attached debugger section using the CY7C65215. The connections of the CY7C65215 are a direct copy of the CYUSB3KIT-003 Superspeed kit. (TCK/TDI/TDO/TMS/RST)

By following the instructions in the EZ-USB Suite UserGuide, and using the Cypress USB Control Center and USB Serial Configuration utilities, I have setup my CY7C65215 identically to the one on the SS kit, both show three USB interfaces when connected:

USB-Serial (Dual Channel) Vendor 1
Cypress FX3 USB Bootloader Device
USB-Serial (Dual Channel) Vendor MFG

SCB1 is configured for JTAG. I set this manually at first, but after failures, just read the entire configuration direct from the SS Kit and applied to my CY7C65215 to ensure identical settings.

I am able to reliably use the SCB0 port for UART debug console logging from the FX3S, but am unable to reliably/successfully JTAG. It has worked once or twice, but most often it fails when attempting to load the firmware. I have attempted the same operations with the same firmware on the SS kit and both UART console logging and JTAG work smoothly.

I have read the errata and discussions below about known issues with the use of the JTAG simultaneously with the UART and have disabled the Uart initialization and usage when attempting to use the JTAG.

At this point, the only thing I can identify that is significantly different is the CY7C5215 device version. The SS kit is reporting 1.0.10.2 while my chip is 1.0.3.78 Could this be related to the issues I am seeing? If so, how could I update or acquire a part which is more current?

CY7C65211 cyusbserial.dll library function CyI2cRead() length bug, errata?

Errata 4. JTAG on SCB1 cannot simultaneously operate with I2C/SPI/UART on SCB0.

Hi

I am a developer looking at Cy7c68013 as a replacement for cy7c68001.

When using the Cy7C68001 Device, "BUSACTIVITY interrupt : detected either an absence or resumption of activity on the USB bus." was used to determine the USB disconnection.

Is there a way to detect absence activity on the USB bus on Cy7C68013A?

Hi,

I met the problem when trying to update firmware to a new EEPROM in FX2LP in Windows 10/ 64-bit. The device can't be identified successfully and the application "cyclone" is locked and can't to operate anymore to load a new firmware.

How can I solve this problem? Thanks a lot.

Hello everybody,

I have a project with my team for which we want to use the CYUSBS234 USB-SPI-Bridge. Unfortunately I only found one C ++ library for it. But we need the library for Ansi C, C # and for Windows console applications.

Are there libraries for this and if so, where can I find them?

Thank you for your feedback

Jakob

Hi,

I'm using cy3684 DVK , the windows version is 7 and 10(2 computers) working on Korean version,

The problem is example An66806 hex file does not working.

So my question is  do I need to change some parts of code? or is there a newest version of the example?

sorry for short english.

Regards

Taehyung