- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I want to design a USB-PD application. I want to add PD functionality for a device that has no PD functionality. I also want to show voltage and current values on a I²C display. I am struggled to select the right CCGx device. So, at the end my application will be UFP device only. It will have 2 USB-C connector one for power input, one for power output. The power output USB-C socket will not have USB-PD functionality, maybe only USB 2.0 connections.
Which device CCGx is suitable for my application?
Where can I find UFP CCGx schematics?
Thanks.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
For the UFP design could use low cost IC BCR CYPD3177, it is support PD3.0 function and have BCR HPI (Same as I2C) port which can accessible for PD contract voltage and current. The schematic is on the website: https://www.cypress.com/CY4533
If you want to write the PD firmware by yourselves, below chip you can select:
1. CCG3PA: CYPD3171. The schematic is CY4532 kit:https://www.cypress.com/documentation/development-kitsboards/cy4532-ez-pd-ccg3pa-evaluation-kit
2. CCG4: CYPD4126 (There are no existing schematic can be refer to, but you can refer the datasheet.)
3. CCG3: CYPD3120/CYPD3123/CYPD3121 (You can refer C to DP reference design and remove DP interface. Link: https://www.cypress.com/documentation/reference-designs/ez-pd-ccg3-usb-type-c-displayport-cable-solu... )
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
For the UFP design could use low cost IC BCR CYPD3177, it is support PD3.0 function and have BCR HPI (Same as I2C) port which can accessible for PD contract voltage and current. The schematic is on the website: https://www.cypress.com/CY4533
If you want to write the PD firmware by yourselves, below chip you can select:
1. CCG3PA: CYPD3171. The schematic is CY4532 kit:https://www.cypress.com/documentation/development-kitsboards/cy4532-ez-pd-ccg3pa-evaluation-kit
2. CCG4: CYPD4126 (There are no existing schematic can be refer to, but you can refer the datasheet.)
3. CCG3: CYPD3120/CYPD3123/CYPD3121 (You can refer C to DP reference design and remove DP interface. Link: https://www.cypress.com/documentation/reference-designs/ez-pd-ccg3-usb-type-c-displayport-cable-solu... )
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you very much.
One more question. I also want to connect CCGx device to PC over USB 2.0. To my understanding CCG3 supports USB2.0 but only for Billboard device class? Does it also supports just "normal" serial port bridge over USB 2.0?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
CCG3 have capabilities to support serial port bridge over USB2.0 and it (USB2.0 to I2C) is implemented in the CCG3 C to DP firmware, you can refer to it. For other class, you need implement it in the firmware.
Best Regards,
Lisa