Strictly necessary cookies are on by default and cannot be turned off. Functional, Performance and Tracking/targeting/sharing cookies can be turned on below based on your preferences (this banner will remain available for you to accept cookies). You may change your cookie settings by deleting cookies from your browser. Then this banner will appear again. You can learn more details about cookies HERE.
Strictly necessary (always on)
Functional, Performance and Tracking/targeting/sharing (default off)
2. The WICED sense comes with default firmware loaded to keep advertising the five sensor data ( Gyro, Accelerometer, e-compass,temperature and humidity
3.With in the SDK there is a sample application called wiced-sense , the default applicaiton loaded on all sense tags. You can modify based on your needs and download the application to your hardware using the below make target
If you are having problems with your installer, check that the download size of the installer is roughly 260MB, installer problems are typically caused by incomplete downloads.
The picture below shows a very common error message. Our SDK utilizes a 32-bit version of an Eclipse based IDE which requires a 32-bit version of JRE to be installed. If you already have the 64-bit JRE installed, you will also need to install the 32-bit version as well. The JRE is designed to allow both 32 and 64 bit variants to be installed on the system.
The WICED Sense kit uses a Silicon Labs USB to Serial Device. The TAG3 board uses an FTDI USB to Serial Device. Both should be installed as part of the SDK 2.2.1 installation process. If not, the FTDI drivers for the TAG3 reinstall them using the file /WICED-Smart-SDK/Drivers/dpinst.exe (make sure you access from the command line). The Silicon Labs USB Drivers can be foundWICED Sense Table of Contents
Everything we have for the WICED Sense, such as schematics, drivers, and Android application source code, can be accessed through theWICED Sense Table of Contents. A great post for the WICED Sense is theWICED SENSE Kit BLOGwhich is like a WICED Sense quick start guide.
Some Android devices appear to have issues pairing to the WICED Sense Tag from inside the app, linked is a work-around that should allow you to connect to your Android device:WICED Sense Android Pairing Work-Around
Install it in the platforms folder: ...\WICED\WICED-SDK-3.1.2\WICED-SDK\platforms
Upon installation, you should see the patches in the platforms folder:
2. Running the ISM GUI
Note: If an error or problem occurs for any step throughout the connection process, it is important to unplug the ISM340USB stick, plug it back in and start from the beginning of this tutorial.
In order to run the ISM GUI go to the following folder: ..\Inventek Systems\eS-WiFi\demo and open the es-WiFI.application
plugin the ISM340 USB stick into the PC and identify which COMPORT it is
In the es-WiFi demo GUI, go to Menu > Install Drivers
Once installation is complete, you should see this screen:
Go to device manager, click on the correct COM port and change the following settings
Baud Rate/BPS: 115200
Data Width: 8
Stop Bits: 1
Flow Control: None
We shall now open the Com Ports: To do so go to Setup > Serial Port > Configure/Open
You should see the following screen:
Verify that the correct settings are in place as listed above and press OK to open the COM port.
3. Setting up the SmartBridge Web Application
Note***: Before we begin, it is important to note that every command has to be typed into the command line box. After you type in a command and press send, it will always take you to the main window. It is important to go navigate back to the command line to ensure a much smoother process.
Type in your SSID into the command line box and press send. Once you press send, the program will ask you if the SSID listed above is correct, type in and enter "y" or "n' accordingly.
Once past this step, type in the correct password. Once again it will ask you if the password that shows on the screen is correct. Give the appropriate response.
Once your password is entered, enter your security type and press "y". It will automatically generate an IPv4 address for the SmartBridge web application.
Copy and Paste the given IPv4 address into the internet browser of your choosing. You have now connected to the BT SmartBridge application
4. Connecting to the WICED SENSE
We shall connect the ISM-43340 USB stick with the WICED Sense Kit
We have programmed wiced_sense.c onto the Kit to display all sensor information
Wake up the WICED Sense Kit and press Rescan on the web application
You should see the name: WICED Sense Kit along with an address. Connect with the Kit by pressing the "connect" button right next to the address of the Kit
Once connected, the WICED Sense Kit will show up on the Connection Pairings List. You have now connected the ISM340 with the WICED Sense Kit.
In order to view the GATT profile, we will press the "Details" button. Once pressed, the screen should look like this:
We have now completed the Inventek ISM340 SmartBridge Application Demo. For further questions, please refer to the community forums.