Public Archive Forum Discussions
hi,
I am using CY8CKIT-050 PSOC 5LP DEV KIT.
I added a USB contoller to my psoc project, by the instrctions of the guide.
and when I connect the communication USB port to my PC and try to install the USB driver, and open the Device Manager, I see that my USB device is defined by:
"Unknown USB device (device descriptor request failed)".
I tried to installed the driver by using usb.inf (after editing this file using the new IDs) and it doesnt help.
I am using Windows 8 and used the INF file from the project directory as written in the instructions.
can someone help me with that?
thanks in advance,
Itamar.
Show LessHello all
how can possible control GPIF from inside of cpu(not signal) for example if we have 3 state :
0-Idel
1- read data gpif
2- write date to gpif
and switch between this state decided by cpu but in GPIF designer we just have one fw_trg ?
second is possible set data counter in GPIF dynamically and when state machine updated?
Third how control dma for gpif, for example if sometime cpu should connects to gpif and sometime gpif connects to usb, we should make 2 dma with one consumer or... (assumed CPU sockets is used foe communication between CPU and USB !)?
I have 2 dma between cpu and usb(send and receive), and want have a connection between cpu and gpif (note: question fist for how control state machine from cpu to switch from idle to read or write from gpif) , also in some situation want dma from gpif to usb(probably auto DMA for speed) to transfer some number of data(that cpu know how much). how can handle it?
Thank you in advance
Bests
Show LessIs S34ML08G2 has internal on chip ECC? Or we have to calculate ECC on MCU
We had selected 4Gb (256M x 16) - S34ML04G204TFI01 from spansion but now it is not showing in portfolio.
So, what is the replaced part number against S34ML04G204TFI01?
Best regards,
Vishal Dhanani
Show LessHi ,
I am new to the BLE testing. I am trying to connect a GATT based BLE Server device through CY smart, i can able to connect the device. but while reading the device Information i got the following error.
Error- Read characteristic value failed. Insufficient encryption
Error Description -Access to the attribute failed due to insufficient encryption. Check the security mode and level in the Master Configuration settings dialog and initiate pairing again to encrypt the link.
I have given the following security parameters,
OOB Settings - Disable OBB
Security Mode -Mode 1
Security level -No Security
Bonding - Bondable
Encryption Key Size- 16
So please kindly help to resolve this issue.
Show LessHello Respected,
I need lifecyle status for the below given part numbers, I am not sure whether the mentioned part numbers are from CYPRESS OR SPANSION
S29GL256P12FFIV22
S29GL512P90FFIV12
S29GL512P90FFIV22
S29GL256P90FFIV12
S29GL512P10FFIV12
S29GL512P10FFIV22
S29GL512P11FFIV12
S29GL256P12FFIV12
S29GL256P10FFIV12
S29GL512P11FFIV22
S29GL256P90FFIV22
S29GL256P10FFIV22
Hello,we had buy an CYUSB3KET-003 Demo, and try to use it for an usb device;But,It seem hard to find the fireware
example about USB Device.
Can I simulate USB Flash Disk with CYUSB3KET-003 ?
Have any fireware example that we can do this simulation ?
How can I do it ?
Thanks
Show LessHello,
I think I tried many ways to transmit something out of the uart interface. But really I can not see anything at the output pins.
Yes I have already set up the jumpers J101 to J104 between PIN 1 and 2 and the SPI interface is also at the same pins and I got them to work as I expect. And yes because both interfaces are at the same pins of the fx3 I am using just one of them in the code.
Why is the uart not working?
Show Less