PSoC Creator & Designer Software

On my PC I had to replace the D drive where Creator was installed due to a hardware fault of the drive.

Then I could install PSoC Creator 4.4 successfully, but two problems remain.

1) Update manager: When I start the update manager, the message

"PSoC Creator errro fmk.M0027 Unable to start executable image: (C:\Program Files (x86)\Cypress\Cypress Update Manager\cyliveupdate.exe)", see attached image.

pops up. I installed Creator on the D drive. There is no directorxy named "Cypress Update Manager" nor a file named "cyliveupdate.exe" on the disks.

When I click "Show Details", it says that there is an internal error.

2) Select Debug Target.

After selection of Debug  - Select Debug Target, a window "Select Debug Target" pops up as usual. But there is nothing in this window. See attached image.

I am an experienced user of Creator, and I have PSoC Creator 4.4 installed on other PCs successfully, everything is fine there.

As said above, on this PC, I had to replace the D drive due to a hardware fault on the drive. Maybe Windows got confused because Creator (and other software) suddenly disappeared. I uninstalled everything that was possible, deleted all Cypress files from the disks, cleaned everything from Cypress from the registry, installed and uninstalled Creator several times, still the same problem.

All ideas are welcome since I do not like the idea to re-install Windows completely...

Hello,

I'm not too familier with PSOC terminology yet, so I hope you can understand me:

I'm using a PSOC 5 LP prototyping kit - the stick kind.

How can I get the ADC values out of the ADC so I can use them in hardware?

I think it might be better to draw a picture:

http://imgur.com/J16l3hk 

To be clear: I've gone through the ADC to UART example. From my understanding of how PSOC works, this is not what I want.  From my understanding, the  main loop runs at about 1 KhZ, and I want to be able to access the full 1 MhZ ADC sampling rate.  From my understanding, if I want the full 1 MhZ, then I need to create everything in the top design file, not programatically.

Am I under the correct understanding that whenever I enter something into Main(), it gets executed on the microcontroller portion of the chip?

Best Wishes,

-TJP

I have a power button which cause interrupt and wakesup the system from Deep Sleep.

I would like to add, even only when the system is on (not a sleep),  sort kind of filter, Debouncer or even just the D-FF the filter noise.

the problem is that those components require a clock and when I tried to add it even with Control Register which is initialized to transfer the signal from the

Hello

I am usin PSoC Creator 4.3  with BLE 4200 device.

Why cant't change the setting 'Parity'  in UART Basic tab (if select IrDa mode)?

Is this how it should be?

Thanks.

In summary;

The CharLCD_I2C Component  has been tested with PSoC3, PSoC and PSoC5LP successfully using 2x16 and 4x20 LCD displays. The CharLCD_I2C component sends data over in 4 bit packets which allows it to work with the readily available, very inexpensive PCF8574AT (I2C Serial to Parallel Converter) connected to the Parallel Inputs of the HD44780 LCD module ($3-$4) requiring only 2 I/O pins and a 4 wire connector for a stand alone display. The I2C LCD component provided by Cypress sends data over in 8 bit packets and requires a much less available, more expensive Serial Input LCD Module ($20-$25) that requires 2-4 resistors, 2-3 i/o pins and a 5-6 wire connector for a stand alone display. The Char LCDmp component will work with  only the HD44780 LCD module ($2) but requires 6 i/o pins and an 8 wire connector for a stand alone display.

The Zipped_Files include the CharLCD_I2C component, Datasheet, and Example projects (CY8CKIT-059, CY8CKIT-042).

Please read the Datasheet carefully to avoid building and compiling errors.

Respectfully, Mike