cancel
Showing results for 
Search instead for 
Did you mean: 

PSoC Creator & Designer Software

Anonymous
Not applicable

Hello,

   

I have a serious problem with PSoC Creator. When I am trying to open a existed project or create a new one, the PSoC Creator takes too many time to open the text files (*.c & *.h). For example PSoC did take 20 mins to open 3 text files?

   

I did install / unistall but the problem is still there

   

Any suggestion?

   

 

   

PS Only one time PSoC gave me the error message described on attached PSF file

   

 

   

Thanks

0 Likes
Reply
1 Solution
JoMe_264151
Expert II

Having a workspace with 20 projects is a bit uncommon, I would suggest you to reduce that.

   

A project that was opened with Creator cannot be opened again using a lower Creator version!

   

I strongly suggest you to use Creator 4.0 there have lots of improvements made and a few errors corrected.

   

Keep your programming equipment updated too. Use latest programmer version to update the firmware of kitprog or miniprog3.

   

 

   

Bob

View solution in original post

0 Likes
Reply
14 Replies
JoMe_264151
Expert II

Which OS are you running?

   

 

   

Bob

0 Likes
Reply
Anonymous
Not applicable

Hello Bob

   

I am running Windows 10

0 Likes
Reply
Anonymous
Not applicable

I also notices that Windows Events have recorded the Application Hanging with Event ID 1002, & Track Category (101)

   

Thanks

0 Likes
Reply
JoMe_264151
Expert II

I would suggest you to get in contact with Cypress directly: At top of this page select "Design support -> Create a Support Case" and ask your question again. You will be helped by a Cypress engineer.

   


Bob

0 Likes
Reply
Anonymous
Not applicable

Thanks Bob, I will

0 Likes
Reply
AnkitaS_51
Employee

Hello ,

   

Please check the .NET framework version on your system. You need .NET 4.0 or later.

0 Likes
Reply
AnkitaS_51
Employee


You can use Microsoft .net recovery tool and reset the .net versions installed
 

0 Likes
Reply
Anonymous
Not applicable

Hello:

   

I give me the error message described on attached PSF file, too.

   

I am running Windows XP.

   

What can I do?

   

I can compile, but I can not debugger.

   

Creator 3.3 -> no work

   

But Programmer 3.24.2 OK. It's OK only Programmer.

   

 

   

PD: before Creator 3.3 was working OK, suddenly, it  is not working

   

Thanks.

0 Likes
Reply
JoMe_264151
Expert II

Welcome in the forum, Cristina.

   

Error message is missing...

   

 

   

Bob

0 Likes
Reply
Anonymous
Not applicable

Hello, again.

   

Sorry.  This is the error.

   

One project was working, and then the same project is not working. 

   

I uninstalled Creator 3.3 and I installed again, but it is the same: it is not working.

   

It seems MiniProg3 is not detected by Creator because there are empty windows ("Select debug target"). Device Manager (XP) is detecting, and Programmer 3.24.2 is detecting and it is ok.

   

Thanks.

0 Likes
Reply
JoMe_264151
Expert II

I would suggest you to upgrade to Creator 4.0, which will co-exist with your version 3.3. I assume that the more modern versions of PSoC Programmer do not work together with the 3.3. Afaik Creator 4.0 is not qualified for Windows XP.

   

 

   

Bob

0 Likes
Reply
AnkitaS_51
Employee

Hello Cristina,

   

Please mention whether you have  64 bit operating system  or 32 bit Operating system  .

0 Likes
Reply
Anonymous
Not applicable

32 bit operating system.

   

If I was working ok with Creator 3.3 and Programmer 3.24.2, and all of projects were debugging. All ok.

   

Now, that same project is not working with Creator 3.3. But Programmer 3.24.2 is ok.

   

I have tried to work with Creator 2.2 (I installed it several years ago), the error also appears.

   

When the error appears, down left in the screen: "Selecting target"

   

It seems that Creator is not detecting miniprog3. I am sure miniprog 3 is ok.

   

Menu Tools -> Options -> Port Configuration -> Error2 attachmented (file Error2.doc) 

   

Thanks for your time

0 Likes
Reply
JoMe_264151
Expert II

Having a workspace with 20 projects is a bit uncommon, I would suggest you to reduce that.

   

A project that was opened with Creator cannot be opened again using a lower Creator version!

   

I strongly suggest you to use Creator 4.0 there have lots of improvements made and a few errors corrected.

   

Keep your programming equipment updated too. Use latest programmer version to update the firmware of kitprog or miniprog3.

   

 

   

Bob

View solution in original post

0 Likes
Reply