- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have 1 CY8CKIT-050 and 2 CY8CKIT-030 boards, all no longer CPU supported
by Creator. Do you folks have a service that can update CPU on the board to
latest rev for a fee ?
Tossing these boards would be a sin and an act against engineering humanity 🙂
Regards, Dana.
Solved! Go to Solution.
- Labels:
-
PSoC Creator & Designer Software
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
Creator has a programming host built in. If you can locate the version of Creator that can handle that silicon you don't need the stand-alone PSoC Programmer. Besides, you need Creator to generate a application project that you want to load into the now "not longer supported" IC.
You're best change of getting either kit to work is to work with Infineon to determine which version of Creator to use to program these ICs.
As you indicated, you don't have the budget for wasted HW and this includes a cheap laptop.
"Engineering is an Art. The Art of Compromise."
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
in the engineering humanity world, the kits would go either into the museum (garage wall), an antiquity store (eBay) or the incubarium (storage unit).
I gave second life to few discontinued PSoC kits through eBay. Surprisingly, they are in demand.
/odissey1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Currently, we don't have a support to replace the parts. Kindly, order latest parts from the Cypress and replace the old parts with the latest parts.
Thanks,
P Yugandhar.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
My budget does not allow me to invest in $ 100 boards and have to throw them away.
Regards, Dana.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
I make my own prototyping kits using KIT-059 for about $10.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I too use the 059, but there are times I need the more complete board.
Regards, Dana.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Am I misunderstanding something? The CY8CKIT-050 I have uses a CY8C5868AXI-LP035, which is an MCU still very much supported in PSoC Creator (Unless support has been removed in v4.4 and I'm just not aware? I don't know why this would be the case).
This specific kit may not be in production anymore but you can absolutely still do prototyping on it. You can even still find them on 3rd party distributors as well (Digi-Key and Mouser both have stock).
Shame if these kits aren't in production anymore though. The 050 is my go-to for prototyping thanks to the easy to access I/O and breadboard space.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The early 050 boards had engineering silicon on them, which has been dropped from
the device selector in Creator and programmer facilities.
050 board still in production as far as I know.
Regards, Dana.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
The older engineering Silicon on the 050 board must have worked with an earlier version of Creator.
Since you can have multiple releases of Creator on your system, you can reinstall an older version that worked with this silicon.
Then you can find or create a usable project to load into it. An example is a multimeter-type program that can read an analog input and display the value.
Once programmed you can dedicate this eval board solely for that purpose.
Another common thing I do is to use older eval boards as stimulus for the target eval board design I'm working on.
I realize that the older board is not capable of using the advantages of the later Creator components. Trying to "make lemons into lemonade".
"Engineering is an Art. The Art of Compromise."
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Small issue, system only wants one version of programmer installed,
so one really has to run two systems or a virtual system so that the
two installations do not "see" each other in the hive (Windows).
I even looked at the catalog device files to see if I could hack into the
system the old parts, no luck.
One would think Cypress has a service that does small board runs for it, a cost
effective service, that could be offered to handle what is a simple problem if
one has the equipment.
Regards, Dana.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
If a older version of Creator works, why do you need Programmer?
"Engineering is an Art. The Art of Compromise."
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I worked my way back thru Creator versions, and the ES silicon
was not in the catalog to select. I dont know if the other versions
over wrote that catalog, I assume they do. Maybe my mistake is
not taking off all versions and dedicate a machine to run an old version.
Maybe buy a $ 500 laptop for this, or just get the part replaced on the board
for ....say $ 50. For what I think is a 10 minute job.....not a solder expert here 🙂
Programmer used to program part.....called by creator to program part (I think),
not sure I follow your question.
Regards, Dana.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dana,
Creator has a programming host built in. If you can locate the version of Creator that can handle that silicon you don't need the stand-alone PSoC Programmer. Besides, you need Creator to generate a application project that you want to load into the now "not longer supported" IC.
You're best change of getting either kit to work is to work with Infineon to determine which version of Creator to use to program these ICs.
As you indicated, you don't have the budget for wasted HW and this includes a cheap laptop.
"Engineering is an Art. The Art of Compromise."
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello ETRO.
On 1 old 050 kit, I removed the 5568 PSoC and attached a KIT-059 to the I/O connectors (port-pin for port-pin alignment). That way, I could use all the onboard 050 peripherals as if it was an up-to-date 5LP 050 kit.
As for my other old 050 kit, I use Creator (either version 1 or 2, I'll have to check which one it is). So, I don't know why you can't find the device in selector list.
Several years ago, maybe around 2014, Cypress had a limited time offer to upgrade the old 050 kit with the new 050 5LP based kit. If you missed out, you missed out.