- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am going through the PSoC 6 video lessons. 1-4. I can get code to compile with no errors but when I download program it doesn't work. The program it came with still works. So obviously the LED does not flash every 500 msec for me. I think I'm doing the programming correctly but maybe I am not.
Solved! Go to Solution.
- Labels:
-
Other
-
PSoC Creator Software
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Could you check as follows:
Is there power to the board?
Is there a problem with the cable? Or is there any improvement if replaced with another one?
Is the board recognized by Device Manager?
After pressing the SW3 button lightly to change the mode, press and hold the SW3 button again to return the mode.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi PeBa_4704766,
Please check pin setting for LED.
I have a PSoC6 BLE Pioneer kit rev G and lab1-4 are successful.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Would you check the following page
https://www.cypress.com/documentation/development-kitsboards/psoc-6-ble-pioneer-kit-cy8ckit-062-ble
Especially, the following table.
And please check if the PDL version you are using matches with the board version of your kit.
moto
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Thanks for your reply.
my projects build OK.
I think problem is I cant program. Even though my kit is installed when i go to program I can't see the kit see inserted image . My kit is supposed to use kitprog 2, which is installed on my development board PSoC6 BLE Pioneer Kit
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Could you check as follows:
Is there power to the board?
Is there a problem with the cable? Or is there any improvement if replaced with another one?
Is the board recognized by Device Manager?
After pressing the SW3 button lightly to change the mode, press and hold the SW3 button again to return the mode.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Success!!
Thanks - There is power to board a program that came with the pioneer board
worked.
I use the same cable in other projects and it's fine.
The Board was not recognized by Device manager
I did what you said re SW3 and checked the "device manager", and as you
can see from the attached screen shot image it is now there.
cheers..again
Regards
Peter Barrett
On Wed, 24 Jun 2020 at 18:46, NoTa_4591161 <community-manager@cypress.com>
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Congratulations!
If you have any other problems, please post as a new one.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
May be the following two discussions can be some information for you.
CY8CKIT-062-BLE Setup Only requires PDL 3.0.1
moto
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
You may used a elder version PSoC6 BLE Kit, which cannot support latest version PDL, you may try to change the PLD you used to 3.0.1 and see if LED flashes(Creator-->Tools-->Options-->PDL v3).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear XiaoweiZ_71-san,
Thank you for your marking my answer as Correct Answer!
But I'm afraid that the Correct Answer was the one from Kenshow-san,
========================
Is there power to the board?
Is there a problem with the cable? Or is there any improvement if replaced with another one?
Is the board recognized by Device Manager?
After pressing the SW3 button lightly to change the mode, press and hold the SW3 button again to return the mode.
========================
So would you please mark his answer correct?
Best Regards,
29-Jun-2020
Motoo Tanaka
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
yes I will tomorrow, cheers
Regards
Peter Barrett
On Mon, 29 Jun 2020 at 22:49, Motoo Tanaka <community-manager@cypress.com>