PSoC™ 6 Forum Discussions
Hello,
I am configuring the GATT settings in the PSoC creator (BLE component).
I set the "Artibute MTU size (bytes)" to be 512. At the same time, I made a custom service that is containing 7 custom characteristics, as shown in the following figure.
My question is: is it Ok to set the field length of each characteristic to be 500? Because the Attribute MTU size is set to be 512. Seven characteristics with 500 bytes each will be 3500 bytes in total, which is larger than the Attribute MTU size.
When I set it as 500, and build the project, the PSoC Creator shows the project is successfully built. However, the BLE stack seems stuck during running (sending notifications).
Thank you very much for your kindly help!
Show LessIam trying to find compiler optimization in modustoolbox, not yet found.
I found that on editing CFLAGS variable in the make file will works, but still iam unable to see the optimized code.
Can you please guide me on this ?
Thanks inadvance.
Show LessHello everyone,
I'm working on a project with CYCLE-416045-02 and i'm using bluetooth.
I used the xTimer available in the defaut file for CYCLE-416045-02 BLE to generate a led blink when my uC advertising.
I want to use 2 new leds and i want that they blink.
So for that i have created 2 new Timer and configure my status_led_task.
My problem is the following, when my uC advertising all work good. When advertising finnish all led stop blink but i expected that only advertising led stop to blink.
After different try and modification in my code and don't have find any solution.
Could you tell me if you have advice or if you have meet this problem ?
Best regards,
Max
Show Less
Hi.
I'm using CY8C6137BZI-F54 at my design.
I have 15 analog inputs that are connected to port 9,10.
When I put the pin assignment all the analogs at port 9, there is a worning about routing congestion.
What do I need to do?
BR
Shmuel
Show LessHello,
I have the CY8CEVAL-062S2 with LAIRD M.2 module and running MTB 2.4. If I create any Bluetooth example with the PSoC6 BSP = CY8CEVAL-062S2-LAI-4373M2, I'm unable to open the Bluetooth Configurator in that example. The error message is:
Unable to run external editor: Unable to launch configurator: ../mtb_shared/core-make/release-v1.9.1/make/core/open.mk:179: *** Unsupported tool type - bt-configurator.
Supported types are: capsense-configurator capsense-tuner device-configurator dfuh-tool library-manager ml-configurator project-creator qspi-configurator seglcd-configurator smartio-configurator usbdev-configurator. Stop.
The same error happens if BSP = CY8CEVAL-062S2-MUR-43439M2.
But if BSP = CY8CKIT-062S2-43012, then the Bluetooth Configurator 2.50 can be launched successfully.
What could be wrong?
Thanks!
Show LessWe are evaluating ADC using CY8CKIT-062S2-43012. How can we evaluate multi input ADC feature on PSoC6?
We are evaluating ADC using CY8CKIT-062S2-43012. Please tell me the ADC input signal voltage range.
We would like to evaluate voice recognition feature using CY8CKIT-062S2-43012 EVB. But no mic device is implemented on the EVB.
Please tell me the recommend environment to evaluate recognition feature using PSoC6.
Show LessHi, I am working on a bring up of CYBLE-416045-02, and using the Modus ADC sample code as template.
Originally, the sample code map P10_0 as the input, and I have reading from this pin
Then, I map it to P10_3, and it still work.
My problem is, if I want to have 4 ADC channel reading, e.g. P9_0, P10_5, P10_3 and P10_4, how should I initiate them?
I tried to initiate them under SINGLE_CHANNEL one by one, but got Initialization Failed Error 67240448
Should I define SINGLE_CHANNEL or MULTI_CHANNEL?
If I have to use MULTI_CHANNEL, how can I config it as single end mode? because the sample code comes with differential mode. Those 4 channels are individual reading (0V-3.2V), I do not have VREF for each of them.
Thanks
Show Less
Hello,
I am trying to build a custom windows Firmware upgrader solution for PSOC 6. I tried downloading Qt Creator 8 and imported the project but it always kicks me out saying that the project has errors to build. I even edited the cmakelists file as listed in the documentation:
set(BOOST_ROOT "C:\Users\Questron\Desktop\Projects\OTA Firmware update\boost_1_66_0")
set(QTDIR "C:\Qt\6.3.1\mingw_64")
set(CyBridge_LIBRARY "C:\Users\Questron\Desktop\sample_code")
The batch file or the script file fails running from sample codes directory.
I made the firmware updater for PSOC 5 with USBHid which is not working with PSoC 6,
I would like to get a working example in visual studio probably or please guide in loading the project as it should be.
Show Less