PSoC™ 6 Forum Discussions

Hi All,

I'm using CYW43455 chip for Wi-Fi support. Here I'm using Wi-Fi enterprise feature but, while using this not able to connect with radius server using specific routers(i.e. TP-Link, D-Link). 

Same scenario I tried with Cisco router & able to establish connection properly. If anyone knows regarding this issue please, let me know.

FYI :Referring WICED-Studio-6.6 code for development

Thanks

Hi everyone,

I'm working with the Cypress PSoC 6 board in Mbed OS. I need to develop an AP Mode WiFi example. Are there any examples available? Can you send me some resources to get started?

Thank you.

1. which development IDE  is a good future and which IDE is easier to learn for PSoC 6 MCUs?

2. how many ways can we flash the code for Psoc 6 mcus?

3. How many IDEs are available in the market for developing code for PSoC 6 MCUs?

Hi ,

I am running a PSOC6 USB HID Generic setup ,  The code works from the IMO clock trimmed to  USB mode.

The problem I am currently experiencing is when everything is run from the IMO  clock at 96Mhz  (because it can't go higher  😞   ) the HID enumerates and I can send data .  However, switching this to the external TCXO gives me much more accuracy and a potential for higher core clocks the  HID side does not work anymore although the paths in the Device configurator and dividers are set up correctly .

I principal the initial sources are the only side that changes , so it should not affect the USB enumeration

Below is 4 scenarios on this 2 working and 2 not working. in order to increase the CORE clock I need everything to run from the EXTCLK . The cores need to be CM4 150Mhz and the CM0 75Mhz  , as it is right now this is not possible.

IMO working config below

EXTCLK NOT working 1

Extclk NOT working2

Extclk working 2

Any assistance is welcome.

Regards

C

Hi all

The example: Adding TFT to my project - Infineon Developer Community

I have a question about my project being built in MTB. I'm following the example of using the CY8CKIT-028-TFT on the CY8CKIT-062-WIFI-BT. However instead of that board I'm using the CY8CKIT-062-BLE (the example uses WIFI-BT), but the TFT shield is compatible with both

When I plug my board in and click program (using kitprog3 miniprog4) the screen doesn't appear to display anything. I followed all the steps and ensured I'm using the right BSP for me. No errors are produced on running but i do get this output:

I'm not changing any other settings, I'm following the tutorial, putting the lines of code in and pressing program so not sure if thats where im going wrong

Any ideas?

Kind regards

So am trying to debug the program by adding the breakpoints and am getting this error. What does this error means and how can we resolve it?

Info : SWD DPIDR 0x6ba02477
Error: Failed to read memory at 0xfffff000
Info : SWD DPIDR 0x6ba02477
Error: Failed to read memory at 0xfffff000
Info : SWD DPIDR 0x6ba02477

Hi all,

I want to simulate some basic assembly language code so I understand Arm assembly language better. What I have in mind is very basic. I'm by no means trying to have an actual project. I'll just have a few assembly language instruction do stuff and see how the cpu register change value. I'm pretty sure there is stuff (code) that needs to setup some basic stuff before I can write my code. I'll be using the debugger to step thru my assembly code and look at the cpu registers.  How do I go about making a very very basic project in assembly code so I can do this?  A simulator for the CM4 would work too but what comes up after a google search doesn't seem to be for the CM4... and I have a perfectly working CM0p/CM4 CPUs right here 😁. 

Thanks

Hello all , 

I want to make a custom pcb with PSOC6 device :CY8C6244AZI-S4D93 , 

I have the latest psoc creator but I can't find this device in my device selector , 

In my device selector in psoc creator , when I choose target device ->psoc6

It finds only 53 psoc6 devices , but there is obviously more then that  ,

What to do ? 

Thanks

Hi,

i'm working on a dualcore psoc63 project using keil importing pack from psoc creator and I see if I use keil (ulink pro) to flash the board the section of emulated eeprom is written and if use binary file generated by keil using MinikitProg4 that section of memory is empty.

Do you know why and how to generate a bin file or hex file also for that region?

Thanks