PSoC™ 6 Forum Discussions
Hi,
I have noticed that MiniProg 4 is marked as "Obsolete" on the main online stores like DigiKey, Newark, ...
Is this from Infineon or do these stores just feel like not selling them anymore?
And if this is obsolete what is the replacement?
Show Less
Hello,
Using the PSoC062 Wi-Fi BT schema as reference (https://www.infineon.com/cms/en/product/evaluation-boards/cy8ckit-062-wifi-bt/), I designed my own PCB using the CYBLE-416045-02 chip and PSoC5 LP KitProg 2 (CY8C5868LTI-LP039) programmer with a USB-C connection, as in the attached schematic.
However, when I connect it to computer is is not recognized and nothing happens. Can anyone suggest if I did any mistake?
PS. I checked the power and all the connection on the board and they are fine, but I didn't programmer the PSoC5 LP Kitprog 2 as I didn't know how should I program it.
Best regards,
Horia Modran
Show LessHello, am trying to read the ADC value of 2 pins and i have few PWM pins which uses the clock, but the issue is that when i initialize both PWM and ADC together ADC is not working while reading the ADC value using cyhal_adc_read() & even the clock allocation fails. So i want both PWM and ADC to work together in a single project.
You can download my project from the attachement.
I want the BSP to be as it is. The only change which is allowed is you can enable ILO,CLK_LF and CLK_BAK if necessary, by default I have kept then disabled. But if necessary you can enable. And also i tried the clock block CYHAL_CLOCK_BLOCK_HF but same issue. So please look into it if you can resolve the issue.
The initialization is successful if use CYHAL_CLOCK_BLOCK_HF for both PWM and ADC, but it fails to read the ADC value. I have added a screen shot of debugging I did.
Show Less使用ModusToolbox project creator建立的M4核心的工程,如何建立一个M0核的工程,使用project creator建立dual -cpu empty psoc6 APP会提示创建失败
I am trying to read the ADC value of 2 pins, and there are other pins which i have initialized for other purposes. So when i invoke the configure_timer_event_interrupt_0_out() function in my code, the ADC initialization fails, but when i comment it the ADC initialization is successful. I want ADC to work with the everything without commenting out any part in the code.
I have attached the code for reference.
Show LessNeed working code example with psoc creator for reading data from SDCARD where uses Psoc6
Thanks in advance
I have a customer using the PSoC6 ( CY8C6136BZI-F34 and CY8C6116BZI-F54), they are getting ready to go through UL and they have some questions regarding firmware that can meet the requirements of IEC 60730. It appears that libraries for this are available for certain members of the PSoC family ( PSOC 3/5 and PSOC 4). Unfortunately, it seems that the PSoC 6 does not have a version of these available.
Do you know when this may be come available or who could address this for them?
Show LessHello.
I am using CY8C6247.
I am implementing DFU and want some advice on whether the following configuration is correct.
- Merge M0/M4 application files.
- Write a value indicating DFU entry in the common ram part of the CM4 core, and perform a soft reset.
- After reset, check common ram value in bootloader and proceed DFU.
If there is no specific value, M0 core is executed immediately.
IAR is used, and the APP ID and linker files are changed.
1. bootloader
define CY_APP_ID=0
linker file : dfu_cm0p_app0.icf
2. M0P application
Define CY_APP_ID=1
Linker file : Linker_m0_dfu.icf
3. M4 application
Define CY_APP_ID=2
Linker file : Linker_m4_dfu.icf
I attach the corresponding link file
Thanks.
Show LessHi,
is it possible to flash a PSoC6, in my case CY8CPROTO-063-BLE, from a ARM device?
I want to connect the CY8CPROTO-063-BLE to a Raspberry Pi and want to flash the CY8CPROTO-063-BLE from this raspberry pi. I saw that ModusToolbox is only available for x86. Also I had a look on pyocd, which already contains some cy* targets, but not for the CY8CPROTO-063-BLE. Is there a solution or a way to flash CY8CPROTO-063-BLE from an ARM device like Raspberry?
Thanks.
Heike
Show LessI am trying to establish a BLE connection on a custom PSoC 6 microcontroller board. I am using a BLE example project that was adapted to my board. The layout includes the two crystal oscillators ECO and WCO for BLE. The programme is executed until the function Cy_BLE_Start(), afterwards the system is frozen. It seems that the BLE startup does not work. The ECO and the WCO clk were activated in the settings (see figure). Can anyone help me?
Show Less