PSoC™ 6 Forum Discussions
Hi,
I want to move the mtb_shared folder inside my project dir rather than its current external location, how can I do that ? Do I need to specify the custom path to the make build so that i doesn't tell me to re-run make getlibs ?
Any assistance would be much appreciated. Thank you in advance!
Xin chào cộng đồng, tôi có một dự án đọc cảm biến BME280 + ML8511 trên PSoC 6 BLE Gửi dữ liệu được đọc bởi cảm biến qua BLE
hiển thị trên MIT APP Nhà phát minh
Nhưng tôi đang gặp một vấn đề: trên ứng dụng MIT, khi nhận dữ liệu Float đồng
thời, tôi không thể phân biệt giữa tia cực tím, nhiệt độ,...
Tôi đã tìm thấy một giải pháp có thể chèn dấu ";" vào chuỗi dữ liệu đã gửi và sẽ được tách ra trên ứng dụng MIT!
Tôi đã thử nó và vấn đề là PSoC 6 BLE không thể gửi chuỗi dữ liệu đó!
Tôi không biết những gì tôi đang làm có đúng không? Và lỗi xảy ra ở đâu?
Hy vọng mọi người có thể xem qua dự án và giúp tôi sửa lỗi!
Cám ơn
Hi,
I'm testing Basic_Device_Firmware_Upgrade example on CY8CKIT-062-WIFI-BT.
Is there a way to make it support both USB_CDC and UART?
Thanks and Regards,
YS
What examples demonstrate dynamic switching between Command Mode and XIP mode to write to external Flash that is also used to store code?
From Section 27.2 of the Architecture TRM, “The operation mode is specified by SMIFn_CTL.XIP_MODE. The operation mode should not be modified when the SMIF is busy (STATUS.BUSY is ‘1’).” I.E. Check STATUS.BUSY = 0 before changing modes and performing memory writes." This implies the MODE can be changed dynamically as long as the memory interface isn't busy.
Show Less
Hello everyone,
I'd like to discuss a modification I'm currently working on for the CY8C6347BZI-BLD53 board, using the example code CE220924. This code utilizes the VDAC and DMA components to generate a sinusoidal signal. My goal is to adapt this code to produce a signal with a custom frequency.
To achieve this, I need to generate a new Look-Up Table (LUT) for each frequency and adjust the number of sampling points accordingly. My intention is to modify the "Number of data elements of transfer" parameter for the DMA and then initiate the signal generation process. Here's the code in question:
#define DATACNT (100)
cy_stc_dma_descriptor_t descriptor = {0};
descriptor = *Cy_DMA_Channel_GetCurrentDescriptor(DW0, 0UL);
Cy_DMA_Descriptor_SetXloopDataCount(&descriptor, DATACNT); // Valid range is 1 to 256.
descriptor.src=(void *)sineWaveLUT_5;
descriptor.dst = (void *)&(CTDAC0->CTDAC_VAL_NXT);
Cy_DMA_Descriptor_DeInit(&descriptor);
Cy_DMA_Channel_Enable(DMA_HW, 1);
DMA_Start(descriptor.src, descriptor.dst);
In this code, I first retrieve the current descriptor, then modify the "Number of data elements of transfer" parameter for the DMA. Finally, I initiate and start the DMA. However, I sense there might be errors or improvements needed in this code. I would greatly appreciate your advice on how to correct this part of the code.
Thank you in advance for your valuable assistance. Your suggestions will be highly appreciated.
#CY8C6347BZI-BLD53
Show LessHello,
How can I implement a Shift Register in the top design of PSoC Creator for a PSOC 6? The target device is the CY8C6347BZI-BLD43
Hello,
I am facing a problem to build the matter door lock example using modus shell after changing the matter library from "shared git repo" to "local git repo".
The shell shows linking error when I tried to build the project as shown.
I think this problem is the same as the problem discussed in the following post Solved: Re: Link error occurred in case "matter library" u... - Infineon Developer Community
But I can't find a clear solution in the discussion. Based on my investigation, I have found that the library is built to a wrong directory (ext folder) and by right it should be built to the "libs folder".
I believe that this is the reason that caused the above error. (* Please correct me if I am wrong.)
Can anyone tell me what should I do (for example: modifying the CMakefile) so that the matter library can be built in the correct directory?
Thanks in advance.
Show LessIs there a way to optimize the size of the application by removing any unused libraries or other ways? The -Os option has already been tried; it helps but not in any significant way. If there are other ways to manually remove any unused libraries/source code? We are willing to try anything.
Greg
Show LessWhich are the least expensive uC's with 16-bit or better ADC, I2S out, and FPU?
(I'm not asking about PSoC6, but this forum required me to pick something)
Show LessHello community!
I have a project that reads ML8511 + BME280 + PSoC 6 BLE sensors
Previously when I only had the ML8511 sensor, I could connect BLE and send data via Android APP!
But after adding the BME280 sensor to the project, the BLE connection error occurred!
I think the problem is with my code!
I have attached my project! Hope everyone can take a look and help me revise this project!
Thank!.