PSoC™ 6 Forum Discussions
text.format{('custom.tabs.no.results')}
Hi everyone,
I have two PSoC 6 kits. I have written fimware central and peripheral roles separately. Now, I am triyng to one multirole device and one peripheral. The aim is writing a firmware for multirole device so that it can connect to mobile phone, get data and send it to the peripheral. However, if I configure my kit as shown in multirole app note, then it connects to mobile phone (in this case multirole device is peripheral to the phone), and gets data that I sent, but it can not connect to the peripheral (in this case I designed multirole device as a central to the other PSoC kit).
Do you have any idea where the problem is it? By the way, if you have any simple example related to this issue, could you share it with me?
Have a nice day!
Show LessThis is the post:
capsense tuner through bluetooth with psoc 4 vb
BragadeeshV_41 mentions that this code is able to connect to the Tuner though BLE by using a server and a client. I would like to find out whether this code has now been fully tested and released.
Thank you
Show LessHello,
I'm using CY8CPROTO-062-4343W. I looked at the ADC_basic example that reads two channels asynchronously (one single ended and one diff).
I would like to incorporate a reading of the internal Temperature Sensor as a third channel.
The example uses HAL drivers found here: Hardware Abstraction Layer (HAL)
but, I can't find how to configure a channel to read from the internal temperature sensor.
Is there a way to do it using the same HAL library? or an example that reads the temperature sensor?
Thanks!
Show LessHello,
I'm not sure about analog, so please let me know as following:
It outputs a 2MHz sine wave and receives it with a sensor. The signal received by the sensor is amplified and phase-compared with the original sine wave. Is it possible to configure this amplification and phase comparison with the analog circuit in PSoC4, 5 or 6?
When handling with 2MHz signals, where in the datasheet of PSoC do you determine if an amplifier or comparator is available?
Thanks,
Kenshow
Show LessHi.guys
our project works fine when downloaded with SWD to our PCBA.
We added DFU SDK with UART interface, our application stops at I2C's
There is a posted discussion with similar issue:
Re: PSoC 6 I2C Stops Working When DFU SDK Included
Can you provide a code snipet how this issue was addressed.
I did send the same question to Dheeraj and Ganesh
Thanks
Ben
Hi,
we are developing an application with the CY8C6247BZI-D54 and I couldn’t find a clear answer for the following, or I found contradictory information:
1. Can we reset ONLY 1 core and keep the other one operating in normal power mode? If yes, which core is possible to reset alone, CM0+ or CM4?
2. Assuming it is possible to reset only 1 core, is it possible to “freeze” the GPIOs (or at least a few GPIOs) such that they keep the state while that core is reset?
Thank you
Show LessHello,
I wanted to use the Smart IO feature on PORT 9 of PSoC 6. But I am using only three pins of it and configured it in Smart IO Configurator.
Can I used the remaining pins of PORT 9 as normal GPIO pins ?
Best Regards,
Vivek
Show LessHi,
I believe it is not mentioned as a sensitive part of the design, but just to make sure, I wanted to know if it could be problematic to cross i2c or spi lines with the CIntX ground line in a capsense design (I would guess it is okay, since even crossing with capsense sensor traces is mentioned to be okay)
Thanks!
Show LessIn ce218136_eink_capsense_rtos example,
an error appears in capsense_switchpowermodecallback for a mode that is not in the parameters
of the cy_stc_syspm_callback_params_t struct.
How do I solve this problem?
IDE : Psoc Creator 4.4
F/W Date : Recently Ver ( https://www.cypress.com/documentation/development-kitsboards/psoc-6-ble-pioneer-kit-cy8ckit-062-ble )
Show Less