PSoC™ 6 Forum Discussions
Hi,
We have been using self-capacitance (CSD) to measure proximity. However, we have observed that the raw count drifts despite the lack of environmental change. Our experimental environment was held at constant temperature and humidity. There was also no movement of any objects over the window of the experiment (5 mins). We tried using both a button widget and a proximity widget for the measurement but we have repeatedly observed a 100-200 drift of the raw count. Are there any settings that could be changed to mitigate this situation?
Thank you for your help!
Show LessHI
What is the output voltage and output current of the dac 12 bit in psoc6 (CY8C6137BZI-F34)
thanks
Hello,
I am trying to do the following application :PSoC 6 MCU with BLE Connectivity: RTC with Current Time Service (RTOS) (infineon.com). But I am using an OLED display. I want to display the time on the screen and be able to connect it to a phone through Bluetooth. I have attached the project. Can anyone help?
Thank you,
Ali Issa
Show LessHi,
I create a project, using CY8C61137BZI.
I'm using all the IOs that the device has.
I did only the drawing to allcate all the pins.
When I build the project, I'm getting errors regarding few output pins.
I attached the project.
BR
Shmuel
Show LessThis is for Windows 10, Modustoolbox (latest) and CY8C624AAZI-S2D44 (these were early, 4 yrs old, engineering samples. COVID delayed everything)
I managed to create a custom BSP for my board (using latest modustoolbox) and now I'm trying to program some functions to check the board. Other than a warning about kitprog3 needed to be updated it programs without errors. I have a couple of debug LEDs connected (P8.2 and P8.3). LEDs turn on when a ground (low) is present at those pins. I can't get that done. I'm using the Empty PSoC 6 app to create a project from my BSP (Import BSP). I was trying to use code to output a low on the LEDs pins but I'm so new at PSOCs that I decided to just leave the For(;;) in the main function empty and try to set the pins in the device configurator to low for the LEDs and High on some others to see if that's working. Nope, nothing works. It looks like the pins are floating. The drives for outputs is set to "strong drive, input buffer off". I've changed the oscillator from a crystal (P12.6 and P12.7) to the internal osc. but still nothing. I tried to output the internal clock to "external pin" and I see nothing on P0.5.
I read here that the first thing at start time is "Executes any hardware-specific initialization code". Is this the device configurator settings?
I do have the WCO enabled and connected. I saw a message in the device configurator that this will delay startup until ...something. What if there is something wrong with my hardware and the WCO never starts? will this prevent the startup sequence from executing?
Any help is appreciated. Thanks.
Show LessHi all
I am struggling with my CY8CKIT-062-BLE kit code example. What I am trying to do is graph on the EPD display the thermistor value, which I believe there is an example of
However I can't find this example code
Could anyone send a link if they know where this example code is?
Thanks
Show Less
Hello,
When I use ic2 for writing and reading date to slave chip, I met a problem as follows.
When I write data to slave chip and in the processing of writing, read function be called. In this situation,
read process should not be executed because i2c bus is busy.
Question 1:
Is there any possible that when BUS_BUSY of SCB_I2C_STATUS is 0 and SR_VALID of SCB_TX_FIFO_STATUS is 1?
Question 2:
Is is necessary to set CLEAR of SCB_TX_FIFO_CTRL to 1 to clear TX FIFO and shift register?
Thank you very much!
Show LessHello,
I have attached my project. I would like to display the voltage of pin 3. Can someone please check if the formula is right?
Thank you,
Ali Issa
Show LessHello,
I would like to display the voltages for pin_3 ,temp_sens and battery-level . Can someone help with the code please? I have attached the project.
Thank you
Show Less