cancel
Showing results for 
Search instead for 
Did you mean: 

PSoC 5, 3 & 1 MCU

Anonymous
Not applicable

hi developers,

   

          I would like to know about the input protection capabilities for PSoC I/O pins. specifically are there any protection diodes on I/O pins of any PSoC IC.if so how much power they can handle.?

0 Likes
1 Solution
Anonymous
Not applicable

Most IC now have ESD protection on the pins, but I would use external clamping diodes in all IO's. For those IO's goes outside the board, and have chances of having some kinds of ESD, I would all TRANSORB type device as well.

View solution in original post

0 Likes
7 Replies
Anonymous
Not applicable

Most IC now have ESD protection on the pins, but I would use external clamping diodes in all IO's. For those IO's goes outside the board, and have chances of having some kinds of ESD, I would all TRANSORB type device as well.

View solution in original post

0 Likes
Anonymous
Not applicable

thanks lleung for the reply. i have some more doubts. this is regarding some fundamentals. would'nt the transient in the input lines if shorted to a supply rail through a protection diode, cause the whole of supply rail to increase its level and affect circuits connected to the same rail.?

0 Likes
AzGa_264406
New Contributor

 If the sourse of transient is more powerful in compare with rail voltage sourse, then the transient current can to change the rail voltage. Proportionally the difference between the sourses. In the case you should take care for transient current attenuating before it comes to input line.

0 Likes
ETRO_SSN583
Esteemed Contributor

In CMOS there is a parasitic SCR if triggered will short the Vdd to Vss rail inside

   

the part and typically blows open the chip bond wire for Vdd rail. It is current sensitive,

   

and of course SCRs have a senstivity to dV/dT on the gate as well. The 29466 has a

   

latchup current rating of -25 & + 50 mA into any pin, above this SCR can potentially get

   

triggered. The part also has an actual latchup current rating of < 200 mA, so in this case

   

bond wire will remain intact.

   

 

   

If the SCR does not get triggered the input protection diodes will turn on and dump

   

charge into the substrate potentially causing logic and other circuits to potentially fault.

   

 

   

So use external clamps, preferably schottky diodes to make sure they tunr on before

   

internal protection diodes.

   

 

   

Some reference material http://www.ti.com/lit/an/sdya009c/sdya009c.pdf

   

 

   

Regards, Dana.

0 Likes
Anonymous
Not applicable

In PSoC 1 device, you should not exceed 0.5V above Vdd and go 0.5V below Vss at any IO. This is the specification for continuous drive. As far as ESD is concerned, IOs can handle 2000V. For higher ESD handling capability, it is recommended to use transient suppressors like TPD1E10B09 at the ESD susceptible port pins.

   

 

   

If you are worried about transients of much longer duration (not ESD), you can zener diodes at the pins.

   

 

   

-Rajiv Badiger

0 Likes
ETRO_SSN583
Esteemed Contributor

Zeners have very fast avalanche switching, so in the right application they can be

   

very beneficial. But their Vz >> Vdiodesilicon >> Vdiodeschottky. So if you are trying

   

to clamp I/O on transients, you need to use the lowest threshold device you can get

   

your hands on. For clamps on Vdd zener most appropriate.

   

 

   

Another approach to think about - http://www.digikey.com/Web%20Export/Supplier%20Content/AdvancedLinearDevices_1014/pdf/ald-tech-volta...

   

 

   

 

   

Regards, Dana.

0 Likes
ETRO_SSN583
Esteemed Contributor

A couple more references -

   

 

   

http://www.fairchildsemi.com/an/AN/AN-600.pdf

   

http://www.zarlink.com/zarlink/msan107-appnote.pdf

   

 

   

Regards, Dana.

0 Likes