PSoC™ 5, 3 & 1 Forum Discussions
1.One of my machines runs under Win Vista and I am not able to install all four needed drivers, only two of them get installed
When I connect the Kit to USB the files are searched in Windows Update... and not found.
Is there an alternate source where I can download the drivers from?
2.how could I solve this proble.
Error: trn.M0004: PSoC Programmer is not installed on your computer system. Device programming and debugging functions have been disabled.
I have read http://www.cypress.com/?app=forum&id=2232&rID=84336 and http://dangerousprototypes.com/forum/viewtopic.php?t=3105&p=57759 andhttp://dangerousprototypes.com/forum/viewtopic.php?f=56&t=2823&start=30#p30169 but one thing that has not been clearly documented is WHERE this information came from.
I've also read the HSSP app note (AN73054) at http://www.cypress.com/?rID=57435 but this is a more generic document, not a specific document for the FX2LP based programmers.
The CY8CKIT-003 documentation shows the FX2LP connections (PD0 = SWDIO, PD1 = SWDCLK, PB2 = XRES#), but does not document which hex file to load. The CY8CKIT-050 has the same FX2LP schematic.
I'm using one of the LCSoft FX2LP devkits inexpensively available on eBay such as http://www.ebay.com/itm/EZ-USB-FX2LP-CY7C68013A-USB-EEPROM-Develope-Board-Module-Logic-Analyzer-/271218602045. I've used this board in other projects and it works great, the hardware is not broken.
In the PSoC Programmer Service directory I see a number of firmware files:
- DVKProg_5_simfw
- DVKProg_fw
- ftk_3_simfw
- ftk_5_simfw
- fx2lp_fw
- rv2_miniprog3fw
- rv5_miniprog3fw
What is the difference between all of these files? What does _simfw signify? Is DVK the on-board development kit programmer firmware? Is FTK for the first touch kits for PSoC3 and PSoC5? What is the generically-named fx2lp_fw for? The .txt file gives the versions of these files but not what they are intended for.
Is the source for any of these available and if so, where?
Some schematics I've seen have a secondary pair of SWDIO/SWDCK lines at PB0/PB1 and they seem intended for the USB SWD pins on PSoC5. Is this true? Can either pair (PD0/PD1 and PB0/PB1) be used or is the USB SWD connection protocol different?
If I want to program a PSoC5LP with the FX2LP dev kit, which should I use? How about a PSoC42xx?
Show LessAll,
I have a question regrading the following functions third inpur parameter, current. The function is implemented in CyLib.c.
CyPLL_OUT_SetPQ(uint8 pDiv, uint8 qDiv, uint8 current)
In the function header, it is mentioned that,
* uint8 current:
* Valid range [1 - 7]. Charge pump current in uA. Refer to the device TRM and
* datasheet for more information.
Unfortunately I could not find much detailes on the TRM regrading this. If anybody has come accross the details, if it is possible please share it here. Further, if i set it to 5, is that means this current is 5uA?
Thanks.
-Anuradha
Could anybody tell me how to configure the pins on CY8C4014SXI421 ? I am using the PSoC Creator 3.0.
Hello all,
Can somebody kindly expalin me the difference of following two Sleep mode invocations?
CyPmSleep(PM_SLEEP_TIME_CTW_4MS, PM_SLEEP_SRC_CTW);
CyPmSleep(PM_SLEEP_TIME_CTW_4MS, PM_SLEEP_SRC_NONE);
Thanks.
-Anuradha
Show Less
Can i get controller board with respective accessories
1.PSoC3 Controller Board - CY8C3446-AXI099
• With USB interface
• All the GPIO taken out by FRC connector
2.PSoC5 Controller Board - CY8C5568AXI-060
• With USB interface
• All the GPIO taken out by FRC connector
kindly advice me for the above.
Thanks and Regards,
Kamaraj M.
Show LessCan anyone help me to configure a pin as digital output in PSoC 5.4? I need to set up the register. When I first run the program, the output must be "1" and then when I press a key it goes to "0". I've tried to set up the pin using the chip editor, but its not working properly.
Show Less