PSoC™ 5, 3 & 1 Forum Discussions
I am new to PSOC 5 while i am using FreeSoc2 i am getting this error,Pls help me to sort out of this error
An internal error occurred in the fitter: (Error running "C:\Program Files (x86)\Cypress\PSoC Creator\3.2\PSoC Creator\bin/cysjtools.exe": System.ComponentModel.Win32Exception: Access is denied at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo) at System.Diagnostics.Process.Start() at CyDesigner.PSoC.P3Fit.Common.TimingAnalyzer.CyStaSjInterface.Run()).
thanks in advance
Show LessHi, I'm new to PSoC but not to embedded controllers and making things talk to each other and then tell me or do for me what I want. A project I am investigating has the below functional high level design. The intent is to embed low cost development boards in the product to establish and determine demand. My expectation is in the low hundreds, so a PCB design may or may not happen.
The parts I'm researching are specifically the mass storage and the CAN and K-Line implementation.
Mass storage:
The CY8CKIT-059 has a micro USB connector on the target: can this be a "Host" to a USB thumb drive via "host adapter cable"? I've been reading the forums and this thread suggests no existing easy solution. Or am I missing something and using this port as USB host is physically/electrically impossible? I did also find "emUSB-Host - USB host stack" software on Segger but do not understand how that would apply to the CY8KIT-059 board.
Alternatively, I have used SD cards before with arduino, etc, but I'm wanting to use the CY8CKIT-059 as is with minimal additional components. If anyone knows of an embedded dev board with SD card in similar price range, I'm interested, however my top choice would be able to host thumb drives.
CAN Transceiver:
Every CAN example I have found immediately assumes the implementation adds a transceiver IC external to the PSoC. Actually, of all the research I've done, only the $19 NXP has the CAN controller with transceiver included in their Cortex M0 implementation. I know in previous research, I saw implementations of CAN transceivers using discrete components, but the best I could find now is this gentleman's circuit using an OPAMP.
Can that circuit be implemented in the PSoc 5LP's analog subsystem? Apologies if the answer would be obvious have I had actual experience with PSoC; I'm still astounded that dragging and dropping blocks in software is replacing a breadboard! The point of this question is to determine if I need to dive head first into PSoC or move on to the NXP for this project.
Conclusion:
If this CY8CKIT-059 devboard is able to perform either Mass Storage or CAN via modular blocks, this board is likely to be my choice. Mass storage isn't a game changer, but if CAN can be had without buying transceivers, I'm going to be happy. And I'll also assume K-Line can be implemented if CAN can.
If any of these "modules" are created by me and helped or perfected by the community's help, I will share how I did it so they can be integrated into PSoC.
The end product will be a small box sealed with epoxy to keep add-ons safe and help protect the IP. I'll probably build them by hand; haven't researched other means for assembly.
Thanks,
Chris
My Psoc 3 module got damaged. I have got many Psoc 1 modules (CY8C28). I want tranfer my logic into PSOC 1 family. Is it possible. Do I have start coding from scratch?
Show LessDear developers ,
This may be very basic. How does one handle sudden level changes in the signal to be digitized by an ADC while it is currently in conversion mode. Does an ADC on the PSoC IC have any inbuilt sample and hold function in its input to maintain a constant input signal level during conversion or does it only have a garbage value when this kind of a situation occurs? please clarify.
Show LessI am currently working on a board designed by a professor at my university using the microcontroller CY8C29466-24PXI, this board controls 12 motors (12 8bit PWMs), has 4 LEDs, 2 switches and 1 LCD display.
So far, using ¨PWMs I've made the robot walk on a straight line but without control, it begins walking as the board and the power source are both ON, so I need to use the two switches to start and stop the motion of the robot, and for that we thought to use one for each action, but I don't know how to integrate the button action to the Block diagram and the main.c code.
Also, I've assigned LED_1 and LED_2 to ports P1_2 and P1_3 respectively, but when i try to iniciate them from the main.c, they don't appear, I begin writting "LED_1_Start();" but the code helper does not show any LED connected.
Thanks beforehand to anyone that could help.
Show LessI want know how much current delivered by GPIO pin ,when M8C runing at 3.2 v ?
Hi,
I want to use a 14 or 16 Bit ADC using my PSOC 5LP Board. I am unable to find it. Only 12 Bit ADC is being shown.
Looking forward for your reply.
Regards
Awais
Show Less