cancel
Showing results for 
Search instead for 
Did you mean: 

PSoC 5, 3 & 1 MCU

Anonymous
Not applicable

 Hi all,

   

Can anyone recommend a good book/tutorial on PSoC C programming for beginners? When I say beginners  I mean people who have never dealt with hardware before. Any help is appreciated. Thank you.

0 Likes
Reply
15 Replies
Anonymous
Not applicable

Hi,

   

I don't think that you will find such thing. I am a beginner in PSoC too and I have spent a lot of time searching for some info, the best I found however was on the Cypress web cite. The C programming is in plain C with some C++ syntax, so there is nothing special. Then you should take a look in the datasheets of every single component you use for the API and more detailed description. I think that you could get some training from Cypress or their partners. 

   

Regards,

   

Stoyan

0 Likes
Reply
Anonymous
Not applicable

Have you looked at the book My First 5 PSoC Designs by Robert Ashby?  I know it's PSoC 3 (insted of PSoC 5) but at the beginner level, they are almost the exact same.

   

 

   

You can download a free softcopy of it here: www.cypress.com/?rID=43123

   

 

   

-Bobby

0 Likes
Reply
Anonymous
Not applicable

hello bobby ,

   

the book u were suggesting is not free i'm a student and new to this psoc 5 desigining.. can u suggest any other links where i can get some info

   

thanks

   

olk

0 Likes
Reply
Anonymous
Not applicable

 The Cypress site has some excellent  "learning" resources, you just have to look for them carefully! If you follow along with the video projects, they are a great help for newcomers. They are all available via 'Cypress University'.

   

Also, the whitepapers are an excellent resource. One of the DMA whitepapers answered every single question I had about using the DMA with TDs and so on - much better than the straight datasheet or family datasheet.

   

Unfortunately, there aren't a lot of whitepapers, and you have to search the videos for the correct PSoC solution (otherwise you get annoying references to "PSoC 3 or PSoC 5" and "PSoC 3 and PSoC 5 devices" every time they mention the chip type!)

   

One of the trainers is also unaware of some of the technical details, reading range dashes as minus signs or straight dashes and so on, which is a bit distracting, but otherwise the videos are very detailed and helpful.

   

I hope this helps anyone looking here!

   

PCPete

0 Likes
Reply
Employee

 I ran across this while looking for something else.  I get quite a few requests like this so I did a blog post which assembled some of the recommendations I've gotten over the years

   

http://www.cypress.com/?rID=93244

   

Thanks,

   

--Matt

0 Likes
Reply
Esteemed Contributor

This I fopund useful, attached.

   

 

   

Regards, Dana.

0 Likes
Reply
Anonymous
Not applicable

I think the best way to learn PSoC is to test with the example project provided.

0 Likes
Reply
Anonymous
Not applicable

I am new to PSoC and need some guide ness from where I should start.

0 Likes
Reply
Contributor II

Hi Katrina,

   

 

   

as already mentioned, there are almost no such books and even more rarely for PSoC. For my trainees, I use the bottom-up approach: begin with small(tm) projects and/or tasks. This will ensure that the task itself is not too complicated, and the trainees get into first touch with C, port hardware, etc. For example, the first session is about some switches and LEDs, so it's no rocket science. It begins with simple reading the switches and output their state to the LEDs and finishes with a switch configurable moving light.

   

Then the tasks are getting higher levels, e.g. switch and LED matrixes, controlling a LCD, etc.

   

 

   

I think this is the best way to rise the knowledge of both hardware and programming language.

   

 

   

Regards,

   

 

   

Ralf

0 Likes
Reply
Anonymous
Not applicable

Hi Katrina,
Hi Suma
Hi Ashish

   

Everything starts with an Idea 😉
In addition to all the hints given above I only can advice to take the idea you have to build some thing.
Being a beginner myself I have learned to love PSoCs and PSoC Creator. Even though my first project is a quite complex thing. I have segregated it down to smaller, less complex items. Starting from there, with the help of the examples Cypress is providing it was possible to piece things together. Don't be afraid to start and don't hesitate to ask whenever you feel for it.

   

All the Best
Frank

Honored Contributor II

Attached is MIT lecture on PSoC5. Introduction to PSoC.

0 Likes
Reply
Anonymous
Not applicable

I also recommend using the IDE and looking through some of the example projects. I usually find those to be really useful when I'm working with a new component.

Anonymous
Not applicable

Hello.. everybody... I have a problem... I used the PSoC 5LP but with the Serial Port my PSoC send's trash to my PC... My code haven't mistakes and all compile... I have the question What is the problem with my device... and how I solve this problem...

0 Likes
Reply
Esteemed Contributor II

Welcome in the forum. Without your project it's just a guess: mismatching baud rates.

   

Which board are you using? A CY8CKIT-059 ? A -001??

   

Can you please post your complete project so that we all can have a look at all of your settings. To do so, use
Creator->File->Create Workspace Bundle (minimal)
and attach the resulting file.

   

 

   

Bob

0 Likes
Reply
New Contributor

Hi there,

   

Just a hint look at your settings from baudrate, data bits, parity, stop bits and flow control.

   

They should match on both sides.

   

In the UART component and in hyperterminal or other software on your pc.

   

Grtzz. Frank

0 Likes
Reply