Dear Sirs.

Hello,I'm your user from China.I bought several MiniProg3 programmers from your company.I now want to run the ppcli.exe automatically by using batch file,and I need program's IC is <CY8C4146AZI-S433>.but I can't see how to make the batch file from the PDF file your provided<PSoC Programmer CLI User Guide.pdf>.

Can you help teach me?How can I finish the work?

Look forward to hearing from you soon.

Thank you very much!

Hi,

I am new to PSoC and trying to understand it one bit a time. I need help in a project I am working on in which I intend to serially transmit data using NTX0 ,NRX0 (Radiometrix)RF transmitter and receiver modules respectively. I have made hardware connections with one PSoC4 kit and NTX0 and other PSoC 4 kit to NRX0 module.

I have some doubts which I was hoping could get cleared here at the community;

1. What are the blocks I should use in the schematics?(I am using ADC and UART  at TX end, and only UART at the Receiving end)

2. How to configure the pins in PSoC creator at the transmitting end and at the receiving end?

3. How to program the receiver (PSoC  4) to receive the data from the other kit(TX)?

4. How to show this communication using PuTTy?​

Awaiting response.

Thank you,

Arshiya Tabassum

Hello,

I am using a capsense Evalkit (4045) with example Code CE210291.

That Programm is adjusted for a One Button/Sense with low power consumption.

Now I'm trying to modify that programm to work with 8..9 Buttons. I have configure "Capsense" with 7 additional buttons.
Unfortunately still only one Button is detected.

I think I need to add additional code in the main.c, but I am not sure how much I need to change? Maybe it need only one line of code?

I think I have to modify follow line, but I am not sure - maybe somebody can confirm/ give some correction, advice?:

line 176

/* Configure button sensor parameters and connect it to AMUXBUS */

    CapSense_CSDSetupWidgetExt(CapSense_BUTTON0_WDGT_ID, CapSense_BUTTON0_SNS0_ID);

     CapSense_CSDSetupWidgetExt(CapSense_BUTTON1_WDGT_ID, CapSense_BUTTON1_SNS0_ID);

CapSense_CSDSetupWidgetExt(CapSense_BUTTON2_WDGT_ID, CapSense_BUTTON2_SNS0_ID);

CapSense_CSDSetupWidgetExt(CapSense_BUTTON3_WDGT_ID, CapSense_BUTTON3_SNS0_ID);

etc....

line 243              

/* process button widget */

CapSense_ProcessWidget(CapSense_BUTTON0_WDGT_ID);

CapSense_ProcessWidget(CapSense_BUTTON1_WDGT_ID);

CapSense_ProcessWidget(CapSense_BUTTON2_WDGT_ID);

CapSense_ProcessWidget(CapSense_BUTTON3_WDGT_ID);

etc...

line 248 ... line 300

                /* If button is active, reset software counter */

                    if (CapSense_IsWidgetActive(CapSense_BUTTON0_WDGT_ID) ||  CapSense_IsWidgetActive(CapSense_BUTTON1_WDGT_ID) || etc....)

                    {

                        /* Reset the software counter if any button is active. */

                        softCounter = RESET;

                    }

                    else

...

..

/* If button is active, switch to active mode */

                    if (CapSense_IsWidgetActive(CapSense_BUTTON0_WDGT_ID) ||  CapSense_IsWidgetActive(CapSense_BUTTON1_WDGT_ID) || etc....)

                    { 

                       /* If sensor is active in slow-scan mode, skip sleep

                        *  and perform sensor scan

                        */

thank you

Hello,

Our product uses PROC BLE  Module (CYBLE-022001-00), and we are running some emissions test at the Test Labs,And we are using CYSAMRT to run the tests.

And Test Lab folks want the way to control the BLE module Operating frequency. I think there is a CHANNEL MAP selection command under SEND COMMANDS tab,

The 37 bit value could be used to control channels, but I am not really sure which bit controls which frequency.

Could you please confirm if I am on right path or there is other way to control the operating frequency?

Thanks,

Naga.

Hi everyone.

I have some questions. I use CYBLE-022001-00 BLE module.

A device Client

B device Server

I'm working on communication client-server. There is no problem communicating.

I use communication protocol when connecting modules.

Connect packet 0x01 0xC0 blemacid1 blemacid2 cheksum 0x04

I want to pair the modules.

Client module connect to server module with connection package.

I turn off the devices and turn them back on again, I want the client module to connect to the server module pair. I want the client module to connect to the server we have mapped to.

When we want to connect to another server, the reset communication package is sent, then the connection package is sent to connect to the new server.

How can i match modules?

Which methods should I use?

Best Regards.

I have an Upgradeable Stack OTA project, which was previously built in Creator 4.1 update 1 with latest components version. The OTA function works fine if the upgraded firmware generated from 4.1 Update1.

However, I moved to the Creator 4.2 latest version and updated the components versions today and got the issue. After I successfully upgrade the firmware and stack (combined) through OTA, the system stacked in InitializeBootloaderSRAM().

After that I use miniprog3 to reprogram the chip, the stack issue solved and I can update the firmware, built from 4.2.

I just wondering did anyone else find the same problem? Any solution or I need to keep using the same IDE version?

I'm hoping someone can help me with this CYBLE_HCI_INSTANT_PASSED_ERROR issue.  There isn't a lot of documentation surrounding this for PSoC in general but from what I've pieced together with some other forum posts on various sites it seems like a core issue where a peripheral/central doesn't respond in it's allotted time-frame and may not stay connected as a result of this.  People have suggested updating the version of the stack I'm on (3.30) which I have tried (to 3.50) with absolutely no change.  Some iphone/android devices are able to maintain the connection without fault, some get disconnected almost immediately on every connection.  This happens both using our custom app and using off the shelf ble scanner apps.

This is actually the second PSoC 4 product we've produced this year using the CY8C-4248LQI-BL573 part.  On the first part we never encountered this issue.  I've double checked that all the connection settings between the two products are exactly the same but have had no success.

If anyone has any experience or suggestions I'd appreciate it.

Thanks,

Nick